跳转到主内容

Power Cord Removal

仅作为前提条件
本指南仅用作其他指南的先决条件。不能单独食用。

你所需要的

  1. Power Cord Removal, Safety precautions: 步骤 1 中的图像 1,1
    • Before you begin, ensure the device is powered down and cool to the touch.

    • Ensure the machine is unplugged.

    • Turn the power switch counterclockwise into the OFF position.

  2. Power Cord Removal, Remove the screw from the red knob: 步骤 2 中的图像 1,1
    • Use a Phillips screwdriver to remove the screw from the center of the red on/off knob.

  3. Power Cord Removal, Remove the knob: 步骤 3 中的图像 1,2 Power Cord Removal, Remove the knob: 步骤 3 中的图像 2,2
    • Remove the red knob.

    • This component is keyed. During reassembly, ensure it is reinstalled in the correct orientation.

  4. Power Cord Removal, Remove the black cap: 步骤 4 中的图像 1,1
    • Remove the black plastic cap from the center of the switch assembly.

    • This component is keyed. During reassembly, ensure it is reinstalled in the correct orientation.

  5. Power Cord Removal: 步骤 5 中的图像 1,1
    • Use a Phillips screwdriver to remove the two screws securing the yellow switch guide to the switch assembly.

    • During reassembly, ensure this component is installed in the same orientation, with the circle in the 6 o'clock OFF position.

  6. Power Cord Removal: 步骤 6 中的图像 1,3 Power Cord Removal: 步骤 6 中的图像 2,3 Power Cord Removal: 步骤 6 中的图像 3,3
    • Remove the yellow switch guide from the switch assembly.

    • Remove the black plastic spacer from underneath the yellow switch guide.

  7. Power Cord Removal, Remove the upper switch housing: 步骤 7 中的图像 1,1
    • Use a Phillips screwdriver to remove the four screws securing the upper half of the switch housing to the lower half.

    • These screws may not come out of their recesses in the housing once they are completely unthreaded. If some stay inside once loose, don't lose track of them.

  8. Power Cord Removal: 步骤 8 中的图像 1,3 Power Cord Removal: 步骤 8 中的图像 2,3 Power Cord Removal: 步骤 8 中的图像 3,3
    • Lift the upper half of the switch housing off of the lower half."

    • The rubber gasket may fall out of the upper housing during the removal process. Do not forget to reinstall the gasket upon reassembly.

  9. Power Cord Removal, Disconnect the power cord from the frame: 步骤 9 中的图像 1,1
    • Use a 3/8 inch socket to remove the bolt securing the power cord loom clamp to the switch bracket.

  10. Power Cord Removal, Remove the loom clamp: 步骤 10 中的图像 1,3 Power Cord Removal, Remove the loom clamp: 步骤 10 中的图像 2,3 Power Cord Removal, Remove the loom clamp: 步骤 10 中的图像 3,3
    • Remove the loom clamp from the power cable.

  11. Power Cord Removal, Remove the switch housing: 步骤 11 中的图像 1,3 Power Cord Removal, Remove the switch housing: 步骤 11 中的图像 2,3 Power Cord Removal, Remove the switch housing: 步骤 11 中的图像 3,3
    • Use a socket to remove the four 11/32 inch nuts from the on/off switch bracket.

    • During reassembly, use a Phillips screwdriver in combination with the 11/32 inch socket wrench to tighten the bolts securing the switch to the bracket."

  12. Power Cord Removal: 步骤 12 中的图像 1,2 Power Cord Removal: 步骤 12 中的图像 2,2
    • Lift the switch assembly off of the switch bracket.

    • The switch housing bolts may fall out when you remove the housing.

  13. Power Cord Removal, Disconnect the green wires: 步骤 13 中的图像 1,1
    • Use a flathead screwdriver to remove the screw securing the two green ground wires to the switch housing.

  14. Power Cord Removal: 步骤 14 中的图像 1,3 Power Cord Removal: 步骤 14 中的图像 2,3 Power Cord Removal: 步骤 14 中的图像 3,3
    • Separate the green ground wires from each other and move them away from the switch housing.

  15. Power Cord Removal, Disconnect the power cord from the switch: 步骤 15 中的图像 1,1
    • Use a flathead screwdriver to loosen the two screws on the right side of the switch assembly securing the black and white wires from the power cord.

    • During reassembly, ensure each wire is installed in its correct location on the switch.

  16. Power Cord Removal: 步骤 16 中的图像 1,3 Power Cord Removal: 步骤 16 中的图像 2,3 Power Cord Removal: 步骤 16 中的图像 3,3
    • Remove the black wire from the switch.

  17. Power Cord Removal: 步骤 17 中的图像 1,3 Power Cord Removal: 步骤 17 中的图像 2,3 Power Cord Removal: 步骤 17 中的图像 3,3
    • Remove the white wire from the switch.

  18. Power Cord Removal: 步骤 18 中的图像 1,3 Power Cord Removal: 步骤 18 中的图像 2,3 Power Cord Removal: 步骤 18 中的图像 3,3
    • Use a 1-1/16 inch wrench or an adjustable wrench to loosen the power cord's strain relief fitting from the switch housing.

    • Once the fitting is loose enough to turn by hand, twist the power cord and fitting counterclockwise until it is fully unthreaded from the switch housing.

  19. Power Cord Removal, Remove the power cord: 步骤 19 中的图像 1,3 Power Cord Removal, Remove the power cord: 步骤 19 中的图像 2,3 Power Cord Removal, Remove the power cord: 步骤 19 中的图像 3,3
    • Remove the power cord from the on/off switch.

结论

To reassemble your device, follow these instructions in reverse order.

Robert Boyd

于02/01/21注册

26,243 声望

创作了94篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 0

总计 33