简介

Replacing the motherboard will require time and patients as there are multiple steps in this guide. Make sure laptop is powered off and be cautious when working around the board as its cables and plugs may be fragile.

  1. Flip the laptop over with the screen facing down to reveal the bottom panel.
    • Flip the laptop over with the screen facing down to reveal the bottom panel.

    • Unscrew each of the highlighted screws with a Phillips #0 screwdriver.

    添加评论

  2. Use a metal spudger to remove fitting and reveal the screw.
    • Use a metal spudger to remove fitting and reveal the screw.

    • Use a screwdriver with a Torx T7 bit to remove the screw.

    添加评论

    • The SD Card slot is on the top right corner of the device near the headphone jacks.

    • Depress the fake SD Card and release.

    • Pull the fake SD Card out and remove it completely from the slot, as this will help in the removal of the backplate.

    添加评论

    • Lift the back plate starting at the opposing edge to the SD card. Lift from left to right and continue lifting this plate at this angle until it's free from the laptop.

    • Once the backplate is completely off, this will reveal the inside components of the device.

    • Upon reassembly of the back cover, make sure to line up the two headphone jacks on the upper right corner with the holes in the back cover or else it will not seat fully.

    添加评论

    • The battery is the black rectangular piece in the bottom half of the device.

    • Remove six 5mm screws holding down the battery using a Phillips PH0 screwdriver.

    • Lift the battery and separate from its place holder.

    • Do not fully remove the battery as it is still connected by the connector in the top right corner.

    添加评论

    • Using the nylon spudger, disconnect the white plugin.

    • Once the wire has been disconnected you may remove the battery.

    添加评论

    • Remove the two 5mm Phillips #0 screws from the fan housing.

    添加评论

    • Use a nylon spudger to disconnect the wire (red/blue) plug from the motherboard.

    • Be gentle and do not apply too much pressure when removing this plug as the motherboard may be fragile.

    添加评论

  3. 传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    传播 Fixmas 欢乐
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Lift up the wire and peel back the clear protective tape.

    • Split the black protective foam inside the tape in half to uncover the wires.

    • This should make the wires free of all connections.

    添加评论

    • The fan is now free and able to be removed. Lift the fan out of place.

    添加评论

    • Remove the two Phillips #0 4mm screws from the heat sink.

    • Lift and remove the heat sink off the CPU.

    • Reapply thermal paste to the heat sink upon reassembly.

    添加评论

    • Use a plastic opening tool to disconnect the orange daughterboard cable and pull out of the connector.

    • Do the same on other side of the orange cable and remove cable completely.

    添加评论

    • Remove the clear tape covering the Wifi module.

    添加评论

    • Remove one Phillips #0 3mm screw from the Wifi module.

    • Disconnect the wifi module from the motherboard by gently sliding piece out of the port.

    添加评论

    • Using a plastic opening tool, disconnect the plug from the motherboard.

    添加评论

    • Using a nylon spudger, remove the CMOS battery connector cable (red/black) from its port.

    添加评论

    • Using a nylon spudger, disconnect the cable from the motherboard.

    添加评论

    • Use a plastic opening tool to disconnect the black ribbon from the motherboard.

    添加评论

    • Using a plastic opening tool, disconnect the white cable from the port.

    添加评论

    • Remove the screen data cable from its connector.

    添加评论

    • Using a nylon spudger, disconnect the DC power plug connector at the top of the motherboard.

    • Gently remove the whole piece from its holder and place it aside.

    添加评论

    • Remove one Phillips PH0 3mm screw from the top of the motherboard.

    • Gently lift the motherboard out of its casing to fully remove from the device.

    添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Tanner Krygier

于2018年09月17日注册

857 信誉积分

创作了5篇指南

团队

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 20

总计 63