跳转到主内容

简介

How to disassemble and change the Laser Unit.

视频概述

  1. Turn off the console and disconnect all cables.
    • Turn off the console and disconnect all cables.

  2. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws. You must remove the warranty sticker and 4 screws.
    • You must remove the warranty sticker and 4 screws.

  3. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw. After removing HDD bay cover, you will see another 3 screw.
    • After removing HDD bay cover, you will see another 3 screw.

  4. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel. Push there to release and remove upper back bezel.
    • Push there to release and remove upper back bezel.

  5. iPhone 电池维修工具包

    只要 $29.99

    Buy Now

    iPhone 电池维修工具包

    只要 $29.99

    Buy Now
  6. The upper front bezel is harder to remove. The upper front bezel is harder to remove. The upper front bezel is harder to remove.
    • The upper front bezel is harder to remove.

  7. Remove 7 screws to release top cover. Remove 7 screws to release top cover. Remove 7 screws to release top cover.
    • Remove 7 screws to release top cover.

  8. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit. Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.
    • Disconnect two flex-cables and move the Laser Unit. Remove the two screws and the small cable and then take out the Power Supply Unit.

  9. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable. To release the laser unit disconnect this flex-cable.
    • To release the laser unit disconnect this flex-cable.

  10. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel. One flex-cable, for rubbers and the metal bezel.
    • One flex-cable, for rubbers and the metal bezel.

  11. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling. Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.
    • Disconnect this flex-cable and attach it to the new spare part. Let's start assembling.

  12. Assembling, assembling... Assembling, assembling... Assembling, assembling...
    • Assembling, assembling...

  13. Let's test the device before fully assembling it. Let's test the device before fully assembling it.
    • Let's test the device before fully assembling it.

结论

To reassemble your device, follow these instructions in reverse order.

10等其他人完成本指南。

ZFix

于2013年12月09日注册

164,698 信誉积分

创作了305篇指南

团队

Master Techs Master Techs 的会员

Community

286 名成员

创作了809篇指南

Very good job, kudos!

Kevin Borras - 回复

I have found that there are to types of lasers do you sell the second one that does not have the black screws on top but are silver. I have found the one with the silver screws has a smaller laser flex cable and plug. its for the cech-43xx

jack blevinski - 回复

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 20

过去的30天: 86

总计 18,389