跳转到主内容

Planet Eclipse Geo3 Solenoid Replacement

你所需要的

  1. Planet Eclipse Geo3 Solenoid Replacement, Grip: 步骤 1 中的图像 1,2 Planet Eclipse Geo3 Solenoid Replacement, Grip: 步骤 1 中的图像 2,2
    • Remove the four screws from the grip with the 5/64" allen wrench. There are two on each side.

  2. Planet Eclipse Geo3 Solenoid Replacement: 步骤 2 中的图像 1,2 Planet Eclipse Geo3 Solenoid Replacement: 步骤 2 中的图像 2,2
    • Pull the grip away from the frame.

  3. Planet Eclipse Geo3 Solenoid Replacement: 步骤 3 中的图像 1,2 Planet Eclipse Geo3 Solenoid Replacement: 步骤 3 中的图像 2,2
    • Pull the grip through the opening.

    • The grip is connected in the middle and is one piece.

  4. Planet Eclipse Geo3 Solenoid Replacement, Macroline: 步骤 4 中的图像 1,3 Planet Eclipse Geo3 Solenoid Replacement, Macroline: 步骤 4 中的图像 2,3 Planet Eclipse Geo3 Solenoid Replacement, Macroline: 步骤 4 中的图像 3,3
    • Remove the macroline from the fitting by pulling the metal ring around the end of the fitting away while pulling out the macroline.

    • It helps to rotate the collar to create room to pull out macroline.

  5. Planet Eclipse Geo3 Solenoid Replacement: 步骤 5 中的图像 1,3 Planet Eclipse Geo3 Solenoid Replacement: 步骤 5 中的图像 2,3 Planet Eclipse Geo3 Solenoid Replacement: 步骤 5 中的图像 3,3
    • While pulling in the metal ring on the fitting, pull the macroline out.

  6. Planet Eclipse Geo3 Solenoid Replacement, Body: 步骤 6 中的图像 1,3 Planet Eclipse Geo3 Solenoid Replacement, Body: 步骤 6 中的图像 2,3 Planet Eclipse Geo3 Solenoid Replacement, Body: 步骤 6 中的图像 3,3
    • Use 1/8" allen wrench to remove screw behind regulator.

  7. Planet Eclipse Geo3 Solenoid Replacement: 步骤 7 中的图像 1,3 Planet Eclipse Geo3 Solenoid Replacement: 步骤 7 中的图像 2,3 Planet Eclipse Geo3 Solenoid Replacement: 步骤 7 中的图像 3,3
    • Use 1/8" allen wrench to loosen the screw inside the grip on the right side.

    • The screw only needs to be turned a couple of times.

    • Slide the upper frame forward on the rails and remove the screw from the slot to separate the two halves of the body.

    • BE CAREFUL: Do not pull the two frames apart too much or too quickly. This may cause the wires to be damaged.

  8. Planet Eclipse Geo3 Solenoid Replacement, Solenoid: 步骤 8 中的图像 1,3 Planet Eclipse Geo3 Solenoid Replacement, Solenoid: 步骤 8 中的图像 2,3 Planet Eclipse Geo3 Solenoid Replacement, Solenoid: 步骤 8 中的图像 3,3
    • Using the Phillips #0 screwdriver, remove the 2 screws in the solenoid.

    • Remove the solenoid.

  9. Planet Eclipse Geo3 Solenoid Replacement: 步骤 9 中的图像 1,1
    • Pry the board connection with the 2 black wires from the terminal.

    • BE CAREFUL: Do not pull hard by the wires or you may dislodge them from the connection instead of removing the connection from the board.

    • Pull out the wires through the opening in the top of the grip and replace the solenoid.

结论

To reassemble your device, follow these instructions in reverse order.

Rett Triplett

于10/18/13注册

801 声望

创作了8篇指南

团队

Clemson, Team 13-6, Benson Fall 2013 Clemson, Team 13-6, Benson Fall 2013 的会员

CLEM-BENSON-F13S13G6

3 名成员

创作了8篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 5

总计 1,526