修复你的物品 社区 商店

Pipo Smart S1 Battery Replacement

简介

The guide will take you through the process of replacing a dead or defective battery in a Pipo Smart S1 tablet.

你所需要的

  1. Pipo Smart S1 Battery Replacement, Battery: 步骤 1 中的图像 1，3 Pipo Smart S1 Battery Replacement, Battery: 步骤 1 中的图像 2，3 Pipo Smart S1 Battery Replacement, Battery: 步骤 1 中的图像 3，3

    • Insert an iFixit opening tool between the body and display of the tablet at the bottom of the device where the charging port is.

    • Slide the tool along the gap you are creating, moving to the right direction against the mini USB port.

    编辑

  2. Pipo Smart S1 Battery Replacement: 步骤 2 中的图像 1，1

    • Gently pry the body of the tablet and pop the back cover open.

    • Lift the back cover of the device and place it on the side.

    编辑

  3. Pipo Smart S1 Battery Replacement: 步骤 3 中的图像 1，1

    • Lift the edge of the white tape with the iFixit opening tool.

    编辑

  4. Pipo Smart S1 Battery Replacement: 步骤 4 中的图像 1，2 Pipo Smart S1 Battery Replacement: 步骤 4 中的图像 2，2

    • Lift the white tape with your fingers, then lift the yellow tape that holds the battery extension.

    编辑

  6. Pipo Smart S1 Battery Replacement: 步骤 5 中的图像 1，1

    • On the bottom of your tablet, use the Phillips #0 screwdriver to take the two 3mm screws out.

    编辑

  7. Pipo Smart S1 Battery Replacement: 步骤 6 中的图像 1，2 Pipo Smart S1 Battery Replacement: 步骤 6 中的图像 2，2

    • Lift the headphone jack and move it to the other side, placing it on the surface you are working on.

    编辑

  8. Pipo Smart S1 Battery Replacement: 步骤 7 中的图像 1，2 Pipo Smart S1 Battery Replacement: 步骤 7 中的图像 2，2

    • Use a spudger to pry the battery and detach it from the glue underneath it.

    • Be careful not to pinch the battery—lithium batteries are hazardous and prone to short circuiting, and thus burning and/or exploding.

    编辑

  9. Pipo Smart S1 Battery Replacement: 步骤 8 中的图像 1，1

    • Lift the battery and place it a little further away from the positive and negative battery wires.

    编辑

  10. Pipo Smart S1 Battery Replacement: 步骤 9 中的图像 1，1

    • Using your soldering iron, melt the two lead spots to detach the wires.

    • The soldering iron is extremely hot, so handle with caution. Always keep the soldering iron holder next to you when using it so you can return it easily.

    • When reassembling, make sure you solder the right pole to the right spot on the circuit board, as swapping them can burn the motherboard.

    编辑

  11. Pipo Smart S1 Battery Replacement: 步骤 10 中的图像 1，2 Pipo Smart S1 Battery Replacement: 步骤 10 中的图像 2，2

    • Remove the two wires. Then remove the battery completely from the device.

    • Make sure you tape the negative and positive battery wires to keep them from short-circuiting.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Ali Alqallaf

于09/28/16注册

340 声望

创作了3篇指南

徽章: 8

+ 5更多徽章

团队

USF Tampa, Team 3-6, Passmore Fall 2016 USF Tampa, Team 3-6, Passmore Fall 2016 的会员

USFT-PASSMORE-F16S3G6

3 名成员

创作了6篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 3

过去 7 天： 5

过去 30 天： 6

总计 980