简介

This is a guide on how to replace the speakers on a Philips DS3000/37 Audio Dock. Because this repair requires soldering, the soldering technique page linked here might be helpful. 如何焊接和脱焊

  1. Pry off the front fascia by inserting a plastic opening tool between the fascia and white casing.
    • Pry off the front fascia by inserting a plastic opening tool between the fascia and white casing.

  2. Pull the ZIF (zero insertion force) white ribbon out of the circuit board by hand located on the back of the front fascia. Be careful when pulling it out of the connector.
    • Pull the ZIF (zero insertion force) white ribbon out of the circuit board by hand located on the back of the front fascia. Be careful when pulling it out of the connector.

  3. Remove the 10 screws from the black internal housing (6 black screws, 4 silver screws). They are all phillips #1 screws and the black screws are 10 mm in length and the silver screws are 8 mm in length.
    • Remove the 10 screws from the black internal housing (6 black screws, 4 silver screws). They are all phillips #1 screws and the black screws are 10 mm in length and the silver screws are 8 mm in length.

  4. Slowly pry around the black housing with the plastic opening tool to remove it from the back housing.
    • Slowly pry around the black housing with the plastic opening tool to remove it from the back housing.

  5. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  6. Remove the 4 phillips #1 head silver screws from the green circuit board. They are located on the four corners of the board and are 8 mm in length.
    • Remove the 4 phillips #1 head silver screws from the green circuit board. They are located on the four corners of the board and are 8 mm in length.

  7. Remove the black tube (speaker port) by unscrewing the silver phillips head #1 screw (8 mm in length) that connects it to the black housing. Pull it off from where it wraps around the black housing's mating port.
    • Remove the black tube (speaker port) by unscrewing the silver phillips head #1 screw (8 mm in length) that connects it to the black housing. Pull it off from where it wraps around the black housing's mating port.

  8. Remove the 4 silver phillips head #1 screws from the back of the speaker that are 7 mm in length.
    • Remove the 4 silver phillips head #1 screws from the back of the speaker that are 7 mm in length.

  9. Remove the speaker from the black housing.
    • Remove the speaker from the black housing.

  10. Remove about an inch of the black sponge insulation from around the red (positive) and black (negative) speaker wires.
    • Remove about an inch of the black sponge insulation from around the red (positive) and black (negative) speaker wires.

  11. Use the soldering iron to heat up the terminal spots on the speaker and remove each wire (red and black). Use the soldering iron to heat up the terminal spots on the speaker and remove each wire (red and black).
    • Use the soldering iron to heat up the terminal spots on the speaker and remove each wire (red and black).

  12. Strip about a quarter inch of the rubber insulation away from each of the speaker wires (red and black wires) using the 6 inch wire strippers.
    • Strip about a quarter inch of the rubber insulation away from each of the speaker wires (red and black wires) using the 6 inch wire strippers.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Andrew McAuliffe

于2014年02月24日注册

128 信誉积分

撰写一个指南

团队

Michigan Tech, Team 5-7, Lauer Spring 2014 Michigan Tech, Team 5-7, Lauer Spring 2014 的会员

MTU-LAUER-S14S5G7

3 名成员

创作了2篇指南

i hardly difficult to treat 2 defective speakers. i find the flat cable a little loose on the main plate. thank you!!!

araujojraa - 回复

浏览统计数据:

过去的24小时: 0

过去的7天: 2

过去的30天: 21

总计 1,737