简介

This guide will take you through the steps of removing the touchscreen.

Locate the bay door for the battery on the left side of the laptop.
  • Locate the bay door for the battery on the left side of the laptop.

添加评论

Slide the latch to the right and then down to unlock it. Pull out the battery.
  • Slide the latch to the right and then down to unlock it.

  • Pull out the battery.

添加评论

Remove the four hinge screws from the back of the computer.
  • Remove the four hinge screws from the back of the computer.

添加评论

Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver. Pry off the plastic strip which was previously held in place by the screws.
  • Open the laptop and remove the four indicated screws with a Phillips size 0 screwdriver.

  • Pry off the plastic strip which was previously held in place by the screws.

添加评论

Remove the four hinge screws to allow the hinges to rotate up and move.
  • Remove the four hinge screws to allow the hinges to rotate up and move.

添加评论

Remove 16 screws from the top of the closed laptop.
  • Remove 16 screws from the top of the closed laptop.

    • 12 Phillips size 1 screws

    • 2 Phillips size 0 screws

    • 2 Torx size 6 screws (T6)

I found that the Torx screw on my model to be T8.

Harley - 回复

Is the touchscreen & the LCD 1 piece? or are they separate?

Chasity Miller -

Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.
  • Gently break the adhesive seal between the front and rear display cases with a plastic opening tool.

    • You will need to reapply the silicon adhesive during reassembly to ensure watertight seal.

添加评论

Pull the top halve of the casing up revealing the inside of the screen
  • Pull the top halve of the casing up revealing the inside of the screen

添加评论

The top half of the case can be removed by sliding the tabs out from under the hinges. This makes unplugging the screen wiring much easier
  • The top half of the case can be removed by sliding the tabs out from under the hinges.

    • This makes unplugging the screen wiring much easier

添加评论

There are 4 wires that need to be unplugged to remove the screen.
  • There are 4 wires that need to be unplugged to remove the screen.

添加评论

For the first wire, peel back the silver cover tape to reveal the connection.
  • For the first wire, peel back the silver cover tape to reveal the connection.

添加评论

Pull the wiring away from the connection to release it.
  • Pull the wiring away from the connection to release it.

添加评论

Remove the 3 strips of black tape as shown to reveal connections 2 and 3.
  • Remove the 3 strips of black tape as shown to reveal connections 2 and 3.

  • Pull the wiring for each away from the connections to remove.

添加评论

The 4th connection is already visible.
  • The 4th connection is already visible.

    • Depending on your model it might not be plugged into anything. If it is, remove it the same way the other 3 connections were removed.

添加评论

Using a plastic opening tool, lift the screen as shown from the case and pull free. Using a plastic opening tool, lift the screen as shown from the case and pull free.
  • Using a plastic opening tool, lift the screen as shown from the case and pull free.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

5等其他人完成本指南。

Dylan Bloom

于2010年04月12日注册

262 信誉积分

创作了4篇指南

团队

Cal Poly, Team 27-93, Amido Spring 2010 Cal Poly, Team 27-93, Amido Spring 2010 的会员

CPSU-AMIDO-S10S27G93

4 名成员

创作了12篇指南

This guide is good for replacing the LCD screen, but it is not complete for the touchscreen panel, which requires some more delicate and precise steps. I think the title of the guide needs to be changed.

Thanks

Alessandro Cervelli - 回复

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 5

过去的30天: 32

总计 15,167