简介

In order to repair the problems that may arise while using the Panasonic PV-GS9 you must disassemble the camcorder entirely. This will allow you to have three large pieces of the camcorder from which all the repairs can be made.

配件

无需配件。

  1. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder. Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.
    • Using a plastic opening tool, remove the record/playback and record/power control knobs from the camcorder.

  2. Open the tape compartment. Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.
    • Open the tape compartment.

    • Using a #00 Phillips head screwdriver, remove the two 4.5mm screws from the camcorder.

  3. Use a plastic opening tool to remove the gray trim piece from top of the camcorder. Take care when removing the trim piece. The plastic parts are fragile and can break easily. Take care when removing the trim piece. The plastic parts are fragile and can break easily.
    • Use a plastic opening tool to remove the gray trim piece from top of the camcorder.

    • Take care when removing the trim piece. The plastic parts are fragile and can break easily.

  4. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  5. Rotate the camcorder so that the eye piece is facing you, and remove the battery. Remove the four black 4.5mm screws, which sit behind the battery. Then, remove the 5th screw to the right of the battery dock.
    • Rotate the camcorder so that the eye piece is facing you, and remove the battery. Remove the four black 4.5mm screws, which sit behind the battery. Then, remove the 5th screw to the right of the battery dock.

    • Be careful not to lose any screws whilst trying to remove them.

  6. Rotate the camcorder so that the tape compartment is facing you. Remove the single 4.5mm black screw, which is above the hook for the hand strap. It may help you during this step to undo the strap on one end.
    • Rotate the camcorder so that the tape compartment is facing you. Remove the single 4.5mm black screw, which is above the hook for the hand strap.

    • It may help you during this step to undo the strap on one end.

    • Next, rotate the camcorder so that the lens is facing you. Remove the single 4.5mm black screw from the front panel.

  7. Rotate the camcorder so that the bottom is facing towards you. Remove the single remaining 4.5mm black screw from the bottom. Next, while still having the bottom of the camcorder facing you, remove the four silver 4.5mm screws from the body.
    • Rotate the camcorder so that the bottom is facing towards you. Remove the single remaining 4.5mm black screw from the bottom.

    • Next, while still having the bottom of the camcorder facing you, remove the four silver 4.5mm screws from the body.

  8. Open the LCD screen on the side of the camcorder.
    • Open the LCD screen on the side of the camcorder.

    • Using a #00 screwdriver, remove the two 4.5mm silver screws located on either side of the hinge of the LCD screen.

  9. Very carefully remove the front cover from the main body of the camcorder. This should come apart with relative ease, however a plastic opening tool may help you remove this panel a little more easily.
    • Very carefully remove the front cover from the main body of the camcorder.

    • This should come apart with relative ease, however a plastic opening tool may help you remove this panel a little more easily.

    • There is a ribbon cable attached to the front panel and the camcorder body, so be careful not to pull that off when you remove this panel.

  10. Using your fingers, carefully pull the ribbon cable away from the logic board. Using your fingers, carefully pull the ribbon cable away from the logic board.
    • Using your fingers, carefully pull the ribbon cable away from the logic board.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Trevor Johnson

于2010年04月18日注册

31 信誉积分

创作了2篇指南

团队

Cal Poly, Team 7-9, Maness Spring 2010 Cal Poly, Team 7-9, Maness Spring 2010 的会员

CPSU-MANESS-S10S7G9

4 名成员

创作了8篇指南

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 2

总计 2,267