简介

This is the circuit board that the AV chord attaches to for transferring images.

配件

无需配件。

  1. Remove the battery and memory card from the device.
    • Remove the battery and memory card from the device.

  2. Remove 4 screws from the right side of the camera.
    • Remove 4 screws from the right side of the camera.

      • There are two 3.4mm screws at the top.

      • There are two 2.2mm screws at the bottom.

  3. Remove the single 3.4mm screw on the left side of the camera.
    • Remove the single 3.4mm screw on the left side of the camera.

  4. Remove 5 screws from the base of the camera.
    • Remove 5 screws from the base of the camera.

      • There are two 2.2mm screws next to the battery compartment.

      • There are three 4mm screws around the tripod mount.

  5. Slowly slide the back cover away from the device
    • Slowly slide the back cover away from the device

      • The back casing is held in place by two ribbon cables. Do not pull the back cover too far from the camera.

  6. Detach both ribbon cables using a spudger. Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.
    • Detach both ribbon cables using a spudger.

      • Use the tip of the spudger to lift the black clip upward, unlocking the ribbon cable.

  7. Remove the back casing from the camera.
    • Remove the back casing from the camera.

  8. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修,即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  9. Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip. Carefully remove the function switch cover. This unit snaps on and off.
    • Use the spudger to remove the ribbon cable connecting the lens casing to the circuit board by lifting up the black clip.

    • Carefully remove the function switch cover. This unit snaps on and off.

  10. Carefully unsnap the front logic board from the rear logic board using a spudger.
    • Carefully unsnap the front logic board from the rear logic board using a spudger.

  11. Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera. Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.
    • Slide the entire top part of the camera that is attached to the logic board, horizontally away from the camera.

  12. Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger. This leaves you with the logic board and the top connection panel separate and free from the camera This leaves you with the logic board and the top connection panel separate and free from the camera
    • Remove the ribbon cable from the top connection panel by unlocking the black clip with a spudger.

    • This leaves you with the logic board and the top connection panel separate and free from the camera

  13. Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.
    • Use a spudger to detach the ribbon cable from the circuit board. Lift the black clip up to unlock it as before.

  14. Remove the 3 screws holding the lens assembly in place.
    • Remove the 3 screws holding the lens assembly in place.

      • The two screws on the left are 4.5mm with washers.

      • The single screw on the right is 4mm.

  15. Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.
    • Push the lens assembly slightly toward the circuit board, and pull the left side out of the casing first. You will have to wiggle this out gently.

  16. Remove the entire assembly out of the casing. The ribbons on the left and bottom of the assembly simply rest on the camera housing.
    • Remove the entire assembly out of the casing.

      • The ribbons on the left and bottom of the assembly simply rest on the camera housing.

  17. Use the spudger to unclip the top ribbon cable from the circuit board.
    • Use the spudger to unclip the top ribbon cable from the circuit board.

  18. Remove the single 2mm screw in the bottom right corner of the circuit board
    • Remove the single 2mm screw in the bottom right corner of the circuit board

  19. Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove. The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.
    • Gently slide the circuit board out away from the port connections. Pull it toward where the lens used to be. Some wiggling may be necessary to remove.

      • The circuit board is fitted into slots attached to the side of the camera. Do not angle upwards to remove.

  20. Take note of how the slots fit into the circuit board for easy replacement.
    • Take note of how the slots fit into the circuit board for easy replacement.

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

Kevin Lufkin

于2010年10月11日注册

158 信誉积分

创作了2篇指南

团队

Cal Poly, Team 9-21, Regan Fall 2010 Cal Poly, Team 9-21, Regan Fall 2010 的会员

CPSU-REGAN-F10S9G21

4 名成员

创作了7篇指南

Where can I buy this part? Thanks!

Janx38 - 回复

浏览统计数据:

过去的24小时: 0

过去的7天: 2

过去的30天: 9

总计 7,707