修复你的物品 社区 商店

Panasonic Lumix DMC-F7 Back Case Replacement

简介

Steps for removing the back half of the case and replacing it with a new one.

你所需要的

  1. Panasonic Lumix DMC-F7 Back Case Replacement, Battery: 步骤 1 中的图像 1，1

    • Slide the lock switch to the right so that it is in the unlocked position.

    • Use your finger to slide the battery hatch in the direction of the downward arrow so that the hatch is open.

    • Both battery and memory card should now be visible.

    编辑

  2. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 2 中的图像 1，1

    • Open the battery hatch and then the black cover to expose the battery compartment.

    • The camera used to create these repair guides did not have a battery and memory card.

    • Remove the battery.

    • When installing the new battery, ensure it is in the same orientation as before.

    编辑

  3. Panasonic Lumix DMC-F7 Back Case Replacement, Back Case: 步骤 3 中的图像 1，1

    • Using the Phillips #00 screwdriver, remove the two 2.8 mm screws located under the hatch.

    编辑

  5. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 4 中的图像 1，1

    • Use the Phillips #00 screwdriver to remove the three 2.8 mm screws on the bottom of the camera.

    编辑

  6. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 5 中的图像 1，1

    • Use the Phillips #00 screwdriver to remove the two 2.8 mm screws on the side of the camera.

    编辑

  7. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 6 中的图像 1，2 Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 6 中的图像 2，2

    • Use a spudger to pry open the case at all sides.

    编辑

  8. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 7 中的图像 1，2 Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 7 中的图像 2，2

    • Be careful not to damage the ribbon cable when opening. Ensure it is still attached.

    • Use your fingers to carefully remove the back casing from the front of the camera.

    编辑

  9. Panasonic Lumix DMC-F7 Back Case Replacement: 步骤 8 中的图像 1，1

    • Place the camera on a flat surface with the front side facing down.

    • Use the spudger to flip up the retaining flap and slide the ribbon cable out of the connector.

    • Hold down on the camera's metal casing with one hand. Using your other hand, remove the back case from the rest of the camera.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与14其他贡献者

Alex Penman

于01/28/11注册

463 声望

创作了4篇指南

徽章: 9

+ 6更多徽章

团队

Cal Poly, Team 7-35, Regan Winter 2011 Cal Poly, Team 7-35, Regan Winter 2011 的会员

CPSU-REGAN-W11S7G35

4 名成员

创作了10篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 2

过去 30 天： 4

总计 895