修复你的物品 社区 商店

Panasonic DMC-FZ70 Back Panel Replacement

简介

Prerequisite Only

This guide will show you how to remove the back panel of the camera so that you can access the inside.

Before you begin, make sure that the battery and SD card have been removed from the camera.

你所需要的

  1. Panasonic DMC-FZ70 Back Panel Replacement, Back Panel: 步骤 1 中的图像 1，2 Panasonic DMC-FZ70 Back Panel Replacement, Back Panel: 步骤 1 中的图像 2，2

    • All screws should be removed using a Phillips #0 screwdriver.

    • Using your screwdriver, unscrew the two 5.0 mm Philips screws to the right of the LCD screen.

    编辑

  2. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 2 中的图像 1，2 Panasonic DMC-FZ70 Back Panel Replacement: 步骤 2 中的图像 2，2

    • Flip the camera over to the left side of the screen and unscrew the 5mm Phillips screw found there.

    编辑

  3. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 3 中的图像 1，2 Panasonic DMC-FZ70 Back Panel Replacement: 步骤 3 中的图像 2，2

    • Turn the camera upside down and unscrew the three 5mm screws found on the bottom.

    编辑

  5. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 4 中的图像 1，2 Panasonic DMC-FZ70 Back Panel Replacement: 步骤 4 中的图像 2，2

    • On the top of the camera locate the two rails with a thin sheet of metal on the floor between them.

    • With a metal spudger, lift this sheet and push it out of the rail device to detach it from the camera.

    编辑

  6. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 5 中的图像 1，1

    • Proceed to remove the four 5mm Phillips screws that you just uncovered.

    编辑

  7. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 6 中的图像 1，1

    • Slowly pull on both side of the camera, until both halves begin to separate from each other.

    • Do not pull too hard, as both halves are held together with ZIF connector cables.

    编辑

  8. Panasonic DMC-FZ70 Back Panel Replacement: 步骤 7 中的图像 1，3 Panasonic DMC-FZ70 Back Panel Replacement: 步骤 7 中的图像 2，3 Panasonic DMC-FZ70 Back Panel Replacement: 步骤 7 中的图像 3，3

    • Using a plastic opening tool, carefully flip up the small black levers that attach the ribbon cables to the ZIF connectors on the motherboard.

    • Carefully pull the ribbon cables out of the slot once they have been released.

    • Only the two indicated connectors need to be removed to separate the two halves of the camera.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与6其他贡献者

Alberto Rodriguez

于01/24/17注册

531 声望

创作了4篇指南

徽章: 13

+ 10更多徽章

团队

Cal Poly, Team 21-3, Maness Winter 2017 Cal Poly, Team 21-3, Maness Winter 2017 的会员

CPSU-MANESS-W17S21G3

6 名成员

创作了12篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 1

过去 7 天： 5

过去 30 天： 11

总计 633