跳转到主内容

Palm Centro Speakers Replacement

你所需要的

  1. Palm Centro Speakers Replacement, Disassembling Palm Centro Battery: 步骤 1 中的图像 1,2 Palm Centro Speakers Replacement, Disassembling Palm Centro Battery: 步骤 1 中的图像 2,2
    • Press and slide open the battery cover.

  2. Palm Centro Speakers Replacement: 步骤 2 中的图像 1,1
    • Caution: Turn cell phone off before removing battery!

    • Press battery to the right.

    • Then lift up battery pack to remove.

  3. Palm Centro Speakers Replacement: 步骤 3 中的图像 1,1
    • Phone with battery removed

  4. Palm Centro Speakers Replacement, Back Housing: 步骤 4 中的图像 1,1
    • Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.

  5. Palm Centro Speakers Replacement: 步骤 5 中的图像 1,1
    • Lift the rubber cap at the top right to reveal the sixth screw.

    • Caution: There is a small Palm sticker under the rubber cap. Tampering with or removing this sticker will void your warranty!

    • Remove the six screws using the T5 Torx screwdriver.

  6. Palm Centro Speakers Replacement: 步骤 6 中的图像 1,2 Palm Centro Speakers Replacement: 步骤 6 中的图像 2,2
    • Remove the SIM card so housing can be separated.

  7. Palm Centro Speakers Replacement: 步骤 7 中的图像 1,2 Palm Centro Speakers Replacement: 步骤 7 中的图像 2,2
    • Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.

  8. Palm Centro Speakers Replacement: 步骤 8 中的图像 1,2 Palm Centro Speakers Replacement: 步骤 8 中的图像 2,2
    • Remove the small plastic insert at the bottom of the phone.

  9. Palm Centro Speakers Replacement: 步骤 9 中的图像 1,2 Palm Centro Speakers Replacement: 步骤 9 中的图像 2,2
    • Continue with plastic pry tool all the way around the phone to remove the back housing.

  10. Palm Centro Speakers Replacement, Logic Board: 步骤 10 中的图像 1,1
    • Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.

  11. Palm Centro Speakers Replacement: 步骤 11 中的图像 1,1
    • Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.

    • Be very careful, these electronics are delicate!

  12. Palm Centro Speakers Replacement: 步骤 12 中的图像 1,1
    • Separate the logic board from the case by lifting and pulling out the bottom.

  13. Palm Centro Speakers Replacement, Speakers: 步骤 13 中的图像 1,3 Palm Centro Speakers Replacement, Speakers: 步骤 13 中的图像 2,3 Palm Centro Speakers Replacement, Speakers: 步骤 13 中的图像 3,3
    • Pry the four plastic latches free that connect the antenna to the logic board.

    • Excessive force may damage your logic board!

    • Remove the antenna from the logic board.

  14. Palm Centro Speakers Replacement: 步骤 14 中的图像 1,1
    • The internal speaker is attached to the antenna. To remove it, pry the speaker from the antenna using the tip of your screwdriver.

    • The speaker should be placed back into its spot in the correct position. Take notice of the gold connectors

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Kevin

于04/12/10注册

31 声望

撰写一个指南

团队

Cal Poly, Team 15-49, Garner Spring 2010 Cal Poly, Team 15-49, Garner Spring 2010 的会员

CPSU-GARNER-S10S15G49

5 名成员

创作了12篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 1

总计 1,470