简介

Use this guide to replace the Olympus Stylus 410 speaker.

Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver. Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver. Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.
  • Locate the 3 screws on the outer metal band and remove them with a #00 Phillips screwdriver.

添加评论

Use the spudger to peel off the outer metal band, starting from the bottom of the camera. The metal band it attached to the camera with glue in addition to screws.  Be careful not to bend the band when removing it from the camera.
  • Use the spudger to peel off the outer metal band, starting from the bottom of the camera.

  • The metal band it attached to the camera with glue in addition to screws. Be careful not to bend the band when removing it from the camera.

添加评论

The shutter button can now be removed. It is not connected to the camera and can be lifted off. The shutter button can now be removed. It is not connected to the camera and can be lifted off.
  • The shutter button can now be removed. It is not connected to the camera and can be lifted off.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Remove the memory card. Locate and remove the 2 screws using a #00 Phillips screwdriver.
  • Remove the memory card.

  • Locate and remove the 2 screws using a #00 Phillips screwdriver.

添加评论

Use a spudger around the edge of the case to loosen it. Carefully wiggle the back case off. This may require a fair amount of force. Carefully wiggle the back case off. This may require a fair amount of force.
  • Use a spudger around the edge of the case to loosen it.

  • Carefully wiggle the back case off. This may require a fair amount of force.

添加评论

Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.
  • Locate the 3 internal screws holding on the front of the case. Remove them with a #00 Phillips screwdriver.

添加评论

While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required. Be careful not to completely pull the front case off because it will still be connected with wires.
  • While grasping the interior and the front case, gently pull until they start to come apart. Some light wiggling may be required.

  • Be careful not to completely pull the front case off because it will still be connected with wires.

添加评论

Use a spudger to remove the speaker. It is attached by a double sided adhesive so it should just peel off. Use a spudger to remove the speaker. It is attached by a double sided adhesive so it should just peel off. Use a spudger to remove the speaker. It is attached by a double sided adhesive so it should just peel off.
  • Use a spudger to remove the speaker. It is attached by a double sided adhesive so it should just peel off.

添加评论

Un-solder the wires to remove the speaker.
  • Un-solder the wires to remove the speaker.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Gabriela Igel

于2010年04月15日注册

18 信誉积分

撰写一个指南

团队

Cal Poly, Team 6-13, Maness Spring 2010 Cal Poly, Team 6-13, Maness Spring 2010 的会员

CPSU-MANESS-S10S6G13

5 名成员

创作了9篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 1,304