修复你的物品

维修的权力

商店

OLPC XO-4 Touch Back Cover Replacement

撰写者： Matthew Smith (和另外8个贡献者)
  • 评论： 0
  • 收藏 0

难度

中等

步骤

13

所需时间

15分钟

节

4

标志

0

简介

Use this guide to access the back cover of your OLPC XO 4.0 Touch.

工具

购买这些工具

配件

没有特定配件。

  1. Turn the laptop upside-down, with the handle facing away from you.

    • Turn the laptop upside-down, with the handle facing away from you.

    编辑

  2. Pull the lock tabs towards the green outer edges of the laptop. Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

    编辑

  3. Lift up on the middle of the battery to remove it from the device. Lift up on the middle of the battery to remove it from the device.

    • Lift up on the middle of the battery to remove it from the device.

    编辑

  4. Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side. Rotate the screen 180° and remove the other two screws. You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

    编辑

  5. Remove the green side panel by pressing down on the small green button on the top and sliding the panel up. Repeat the step above for the panel on the other side. Repeat the step above for the panel on the other side.

    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

    编辑

  7. Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

    编辑

  8. Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame. Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

    编辑

  9. Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

    编辑

  10. Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break. Carefully lift the screen out.

    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

    编辑

  11. Notice that the laptop in this picture has been turned 180° with the antennas now below the screen. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs. For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

    编辑

  12. Remove the screen from the laptop.

    • Remove the screen from the laptop.

    编辑

  13. Remove the four 6mm screws using a Phillips #1 screwdriver.

    • Remove the four 6mm screws using a Phillips #1 screwdriver.

    编辑

  14. Rotate the top half of the laptop so that the back cover is facing you. Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与8其他贡献者

Matthew Smith

于2013年01月25日注册

23 信誉积分

创作了4篇指南

徽章: 10

+ 7更多徽章

团队

Cal Poly, Team 3-29, Amido Winter 2013 Cal Poly, Team 3-29, Amido Winter 2013 的会员

CPSU-AMIDO-W13S3G29

4 名成员

创作了20篇指南

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 0

总计 151