跳转到主内容

OLPC XO-4 Touch Back Cover Replacement

你所需要的

  1. OLPC XO-4 Touch Back Cover Replacement, Battery: 步骤 1 中的图像 1,1
    • Turn the laptop upside-down, with the handle facing away from you.

  2. OLPC XO-4 Touch Back Cover Replacement: 步骤 2 中的图像 1,2 OLPC XO-4 Touch Back Cover Replacement: 步骤 2 中的图像 2,2
    • Pull the lock tabs towards the green outer edges of the laptop.

    • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

  3. OLPC XO-4 Touch Back Cover Replacement: 步骤 3 中的图像 1,2 OLPC XO-4 Touch Back Cover Replacement: 步骤 3 中的图像 2,2
    • Lift up on the middle of the battery to remove it from the device.

  4. OLPC XO-4 Touch Back Cover Replacement, Screen Frame: 步骤 4 中的图像 1,3 OLPC XO-4 Touch Back Cover Replacement, Screen Frame: 步骤 4 中的图像 2,3 OLPC XO-4 Touch Back Cover Replacement, Screen Frame: 步骤 4 中的图像 3,3
    • Remove the two 4mm Phillips #1 screws underneath the screen on the right-hand side.

    • Rotate the screen 180° and remove the other two screws.

    • You will have to put your screwdriver through the handle in order to reach the middle screw for both sides.

  5. OLPC XO-4 Touch Back Cover Replacement: 步骤 5 中的图像 1,3 OLPC XO-4 Touch Back Cover Replacement: 步骤 5 中的图像 2,3 OLPC XO-4 Touch Back Cover Replacement: 步骤 5 中的图像 3,3
    • Remove the green side panel by pressing down on the small green button on the top and sliding the panel up.

    • Repeat the step above for the panel on the other side.

  6. OLPC XO-4 Touch Back Cover Replacement: 步骤 6 中的图像 1,1
    • Be careful not to pull the bottom too far out because a ribbon cable is under the frame and can easily break.

    • Gently lift up the lower part of the frame and pull it down to free the screen frame.

  7. OLPC XO-4 Touch Back Cover Replacement: 步骤 7 中的图像 1,2 OLPC XO-4 Touch Back Cover Replacement: 步骤 7 中的图像 2,2
    • Lift the black connector and pull the ribbon cable out by the purple tab, freeing the frame.

  8. OLPC XO-4 Touch Back Cover Replacement, Screen: 步骤 8 中的图像 1,1
    • Remove the four 7.62mm screws using a Phillips #1 screwdriver.

  9. OLPC XO-4 Touch Back Cover Replacement: 步骤 9 中的图像 1,2 OLPC XO-4 Touch Back Cover Replacement: 步骤 9 中的图像 2,2
    • Be careful not to pull the screen out too far. There are two ribbon cables attached to the screen, and they can easily break.

    • Carefully lift the screen out.

  10. OLPC XO-4 Touch Back Cover Replacement: 步骤 10 中的图像 1,3 OLPC XO-4 Touch Back Cover Replacement: 步骤 10 中的图像 2,3 OLPC XO-4 Touch Back Cover Replacement: 步骤 10 中的图像 3,3
    • Notice that the laptop in this picture has been turned 180° with the antennas now below the screen.

    • For each ribbon cable, lift up the black connector and gently pull the ribbon cables out by the plastic tabs.

  11. OLPC XO-4 Touch Back Cover Replacement: 步骤 11 中的图像 1,1
    • Remove the screen from the laptop.

  12. OLPC XO-4 Touch Back Cover Replacement, Back Cover: 步骤 12 中的图像 1,1
    • Remove the four 6mm screws using a Phillips #1 screwdriver.

  13. OLPC XO-4 Touch Back Cover Replacement: 步骤 13 中的图像 1,2 OLPC XO-4 Touch Back Cover Replacement: 步骤 13 中的图像 2,2
    • Rotate the top half of the laptop so that the back cover is facing you.

    • Pull up the tabs on the lower part of the back cover and pull it down and away from the antennas.

    • Remove the back cover by gently lifting it off of the laptop.

结论

To reassemble your device, follow these instructions in reverse order.

Matthew Smith

于01/25/13注册

23 声望

创作了4篇指南

团队

Cal Poly, Team 3-29, Amido Winter 2013 Cal Poly, Team 3-29, Amido Winter 2013 的会员

CPSU-AMIDO-W13S3G29

4 名成员

创作了20篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 4

总计 248