简介

Fix fuzzy, muffled, or a complete absence of sound with a new set of speakers.

配件

无需配件。

Place the laptop upside down with the handle away from you.
  • Place the laptop upside down with the handle away from you.

添加评论

Slide the tabs out, towards the green edges,  to show the open lock symbol.
  • Slide the tabs out, towards the green edges, to show the open lock symbol.

    • The right tab will stay in place, but the left tab must be held in position while you remove the battery.

添加评论

  • Lift the middle of the battery to remove it.

添加评论

  • Turn the laptop so it is resting on its bottom.

  • Open the laptop by rotating the green wings on the side up, then lifting the top half of the laptop.

  • Rotate the top half of the laptop about 90 degrees.

添加评论

  • Turn the laptop upside down, so you can see the screws on the bottom of the top half.

  • Remove the two 4mm screws with a Phillips #1 screwdriver.

  • Rotate the top half 180 degrees.

  • Remove the two 4mm screws with a Phillips #1 screwdriver.

添加评论

  • Rotate the top of the laptop 90 degrees, so that it is facing you again.

  • Slide the green pieces off the device. They should come off easily.

添加评论

  • Pull down on the white screen cover. It does not require much force.

  • Remove the screen cover.

  • The game pad on the left sometimes falls during this step.

添加评论

  • Unscrew the four 7.62mm Phillips #1 screws on either side of the screen.

  • The screen is still connected by ribbon cables. You can damage the cables if you remove the screen before disconnecting the cables.

  • Move the screen down a little to expose the ribbon cables.

添加评论

  • Flip up the tab right under the middle top of the screen.

  • Pull the black ribbon cable out of the socket.

添加评论

  • Flip up the smaller tab under the left side of the screen.

  • Remove the small cable to separate the screen from the rest of the laptop.

  • Gently remove the screen.

添加评论

  • Remove the four 4mm Phillips #1 screws that hold the top cover to the case.

添加评论

  • Close the lid and rotate the device 180°.

  • Press firmly on the top two corners of the outside cover. Then slide it down, away from the antennas.

添加评论

  • Remove the five 4mm Phillips #1 screws securing the EMI shield to the motherboard.

  • Gently lift up and remove the EMI shield.

添加评论

  • Gently remove the two antenna cables by lightly pulling the cable connectors up.

添加评论

  • Remove the two 5mm Phillips #1 screws holding the wireless card to the motherboard.

  • The wireless card will pop up at an angle.

添加评论

  • Remove the wireless card by gently lifting it out of the socket.

添加评论

  • Disconnect the five cables that connect the motherboard to the case by pulling them straight out of their sockets.

  • The motherboard is still attached to the case by a microphone cable. Do not remove the motherboard or you will damage the cable.

添加评论

  • Rotate the device 180° and open the lid.

  • Disconnect the microphone cable by pulling its connector straight out of its socket on the motherboard.

添加评论

  • Close the lid and rotate the device 180°.

  • Lift the left edge of the motherboard and remove it from the case.

  • Make sure that the microphone and headphone jack don't catch on the case as you are removing the motherboard.

添加评论

  • Open the lid, rotate it 180° degrees, and close it again so the speakers are facing up.

  • Pull the speakers out and feed the cables through their holes in the case.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

Wei Xia

于2013年01月25日注册

518 信誉积分

创作了5篇指南

团队

Cal Poly, Team 3-28, Amido Winter 2013 Cal Poly, Team 3-28, Amido Winter 2013 的会员

CPSU-AMIDO-W13S3G28

3 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 174