简介

You need a T5 screwdriver to remove the screws.

In order to remove the back cover, you must press the indicated button.
  • In order to remove the back cover, you must press the indicated button.

添加评论

With the button pressed, apply light pressure and slide the back cover off. This will allow you to access the battery
  • With the button pressed, apply light pressure and slide the back cover off.

  • This will allow you to access the battery

添加评论

In order to remove the battery, pull it out from the same side that the rubber button is on.
  • In order to remove the battery, pull it out from the same side that the rubber button is on.

添加评论

Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone. Using a plastic opening tool, separate the back cover from the phone.
  • Using a plastic opening tool, separate the back cover from the phone.

添加评论

Continue along the edge with the plastic opening tool. Continue along the edge with the plastic opening tool.
  • Continue along the edge with the plastic opening tool.

添加评论

Mac RAM 套件
加速你的Mac。充分利用它的内存。
Mac RAM 套件
从Mac中清理出更多内存。
Gently, remove the back cover. Gently, remove the back cover. Gently, remove the back cover.
  • Gently, remove the back cover.

添加评论

Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver. Unscrew the indicated screws using the T5 screwdriver.
  • Unscrew the indicated screws using the T5 screwdriver.

添加评论

Open the phone up and use the plastic opening tool to remove the cover to the keyboard. Be careful not to break the plastic during this step; do your best not to force anything.
  • Open the phone up and use the plastic opening tool to remove the cover to the keyboard.

  • Be careful not to break the plastic during this step; do your best not to force anything.

添加评论

The button board will be loose once the cover is removed. Lift it up to reveal the sensor board.
  • The button board will be loose once the cover is removed.

  • Lift it up to reveal the sensor board.

添加评论

With the T5 Screwdriver, remove the marked screws. With the T5 Screwdriver, remove the marked screws.
  • With the T5 Screwdriver, remove the marked screws.

添加评论

With the screws removed, the sensor board should be free to flip up. With the screws removed, the sensor board should be free to flip up.
  • With the screws removed, the sensor board should be free to flip up.

添加评论

Disconnect the wire with the plastic opening tool. Disconnect the wire with the plastic opening tool.
  • Disconnect the wire with the plastic opening tool.

添加评论

Remove the screws marked. The Screw on the left is located underneath the cable. With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.
  • Remove the screws marked.

  • The Screw on the left is located underneath the cable.

  • With those screws removed, the circuit board and sensor board will be detached from the rest of the phone.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

Cameron Weinberg

于2011年04月12日注册

444 信誉积分

创作了6篇指南

团队

Cal Poly, Team 18-21, Garner Spring 2011 Cal Poly, Team 18-21, Garner Spring 2011 的会员

CPSU-GARNER-S11S18G21

4 名成员

创作了7篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 3

过去的30天: 16

总计 5,310