修复你的物品

维修的权力

商店

Nintendo Wii Motherboard Cover Replacement

撰写者： Andrew Bookholt (和另外4个贡献者)
  • 评论： 4
  • 收藏 3

难度

中等

步骤

12

所需时间

建议一个时间??

节

1

标志

1

Prerequisite Only

仅作为前提条件

请注意，本指南只是其他指南的前提条件。

  1. Use a pair of tweezers to lift the fan connector up and out of its socket on the logic board.

    • Use a pair of tweezers to lift the fan connector up and out of its socket on the logic board.

    • Be sure your tweezers are clamped down on the fan connector, not the socket on the motherboard.

    翻译

  2. Remove the two 10 mm Phillips screws securing the fan to the fan shroud. Remove the fan from the Wii.

    • Remove the two 10 mm Phillips screws securing the fan to the fan shroud.

    • Remove the fan from the Wii.

    翻译

  3. Use the tip of a spudger or another fine-pointed tool to carefully pry one of the black plastic retaining fingers attached to the fan shroud away from the Wi-Fi antenna board. Lift the Wi-Fi antenna out of the fan shroud.

    • Use the tip of a spudger or another fine-pointed tool to carefully pry one of the black plastic retaining fingers attached to the fan shroud away from the Wi-Fi antenna board.

    • Lift the Wi-Fi antenna out of the fan shroud.

    翻译

  4. Remove the single 10 mm Phillips screw securing the second Wi-Fi antenna to the top of the fan shroud.

    • Remove the single 10 mm Phillips screw securing the second Wi-Fi antenna to the top of the fan shroud.

    翻译

  6. Remove the two pieces of tape securing the second Wi-Fi antenna cable to the plastic bracket near the heat sink.

    • Remove the two pieces of tape securing the second Wi-Fi antenna cable to the plastic bracket near the heat sink.

    翻译

  7. Carefully de-route both antennas from the frame of the Wii and lay them aside.

    • Carefully de-route both antennas from the frame of the Wii and lay them aside.

    翻译

  8. Remove the three 10 mm Phillips screws securing the fan shroud to the Wii. Lift the fan shroud off the heat sink and remove it from the Wii.

    • Remove the three 10 mm Phillips screws securing the fan shroud to the Wii.

    • Lift the fan shroud off the heat sink and remove it from the Wii.

    翻译

  9. Remove the following six screws securing the EMI fingers to the bottom panel: Four 7 mm Phillips screws Two 11.3 mm Phillips screws

    • Remove the following six screws securing the EMI fingers to the bottom panel:

    • Four 7 mm Phillips screws

    • Two 11.3 mm Phillips screws

    • Remove both sets of EMI fingers from the Wii.

    翻译

  10. Remove the following three screws: One 7 mm Phillips screw

    • Remove the following three screws:

    • One 7 mm Phillips screw

    • Two 10 mm Phillips screws

    • Lift the bracket out of the Wii.

    翻译

  11. Remove the three 10 mm Phillips screws securing the black bracket to the bottom panel near the front of the Wii. Slightly lift the bracket and use your other hand to pull the retaining clip away from where the Wi-Fi antennas enter the motherboard sheild. Remove the bracket from the Wii.

    • Remove the three 10 mm Phillips screws securing the black bracket to the bottom panel near the front of the Wii.

    • Slightly lift the bracket and use your other hand to pull the retaining clip away from where the Wi-Fi antennas enter the motherboard sheild.

    • Remove the bracket from the Wii.

    • Be sure not to lose the small square nut loosely held by the black plastic bracket.

    翻译

  12. Remove the nine remaining 7 mm Phillips screws securing the motherboard cover to the bottom panel.

    • Remove the nine remaining 7 mm Phillips screws securing the motherboard cover to the bottom panel.

    翻译

  13. Carefully lift the motherboard cover off the motherboard, minding any cables that may get caught.

    • Carefully lift the motherboard cover off the motherboard, minding any cables that may get caught.

    • On some models, a thermal pad for the wireless chip is attached to the underside of the motherboard cover. Be sure to replace it when reassembling.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

0条评论

添加一条评论

添加评论

浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 6

总计 940