跳转到主内容

Nintendo Wii Fan Replacement

你所需要的

  1. Nintendo Wii Fan Replacement, Faceplate: 步骤 1 中的图像 1,2 Nintendo Wii Fan Replacement, Faceplate: 步骤 1 中的图像 2,2
    • Use a metal spudger to remove the white plastic screw covers stuck to the lower case near the front of the Wii.

  2. Nintendo Wii Fan Replacement: 步骤 2 中的图像 1,1
    • Remove the two 8.3 mm Tri-Point screws hidden under the covers you just removed.

  3. Nintendo Wii Fan Replacement: 步骤 3 中的图像 1,1
    • Remove the single 5.9 mm Phillips screw under the controller port door nearest the faceplate.

  4. Nintendo Wii Fan Replacement: 步骤 4 中的图像 1,1
    • Use a metal spudger to remove the rubber foot stuck to the side of the Wii near the DVD drive opening.

  5. Nintendo Wii Fan Replacement: 步骤 5 中的图像 1,1
    • Remove the single 5.9 mm Phillips screw hidden under the foot you just removed.

  6. Nintendo Wii Fan Replacement: 步骤 6 中的图像 1,2 Nintendo Wii Fan Replacement: 步骤 6 中的图像 2,2
    • Carefully pull the faceplate away from the front of the Wii.

    • Use a pair of tweezers to disconnect the LED cable's plastic connector from the motherboard.

    • Remove the faceplate.

  7. Nintendo Wii Fan Replacement, Outer Case: 步骤 7 中的图像 1,3 Nintendo Wii Fan Replacement, Outer Case: 步骤 7 中的图像 2,3 Nintendo Wii Fan Replacement, Outer Case: 步骤 7 中的图像 3,3
    • Open the controller port cover until it is perpendicular to the black controller port bezel.

    • Pull the controller port cover straight up to release it from the outer case.

    • Repeat this procedure for the memory card port cover.

  8. Nintendo Wii Fan Replacement: 步骤 8 中的图像 1,2 Nintendo Wii Fan Replacement: 步骤 8 中的图像 2,2
    • Remove the two remaining 4.1 mm Phillips screws along the top edge of the black plastic controller port bezel.

    • Lift the bezel from the long edge furthest away from the controller ports and remove it from the Wii.

  9. Nintendo Wii Fan Replacement: 步骤 9 中的图像 1,1
    • Remove the two 5 mm Phillips screws above the controller ports.

  10. Nintendo Wii Fan Replacement: 步骤 10 中的图像 1,1
    • Use a metal spudger to remove the three highlighted screw covers stuck to the side of the Wii.

  11. Nintendo Wii Fan Replacement: 步骤 11 中的图像 1,1
    • Remove the following screws:

    • Two 5 mm Phillips screws

    • One 8.2 mm Tri-Point screw

  12. Nintendo Wii Fan Replacement: 步骤 12 中的图像 1,1
    • Use a metal spudger to remove the two rubber feet stuck to the bottom face of the Wii near the rear ports.

  13. Nintendo Wii Fan Replacement: 步骤 13 中的图像 1,1
    • Remove the two 8.2 mm Tri-Point screws hidden under the feet you just removed.

    • You may use a 4 mm hex driver to extend your bit into the recesses and reach the screws.

  14. Nintendo Wii Fan Replacement: 步骤 14 中的图像 1,1
    • Lift the outer case straight up off the body of the Wii.

  15. Nintendo Wii Fan Replacement, Fan: 步骤 15 中的图像 1,1
    • Grab the fan connector with a pair of tweezers and lift it straight up and out of its socket on the motherboard.

    • Be sure your tweezers are clamped down on the fan connector, not the socket attached to the motherboard.

  16. Nintendo Wii Fan Replacement: 步骤 16 中的图像 1,1
    • Remove the two 10 mm Phillips screws securing the fan to the fan shroud.

  17. Nintendo Wii Fan Replacement: 步骤 17 中的图像 1,1
    • Remove the fan from the Wii.

结论

To reassemble your device, follow these instructions in reverse order.

27等其他人完成本指南。

9条评论

Awesome guide, just replaced faulty fan unit in my 9 year old wii. Should hopefully keep it going for another 9 years :)

Finlay Macrae - 回复

Super easy and great instructions! I feel a little guilty that my Wii sat in the garage for 4 years! Now it'll be a great birthday present for my 2 boys.

e_gayheart - 回复

Does anyone have a diagram for the Wii’s airflow? I’m looking to install a booster fan at the bottom to help blow air in but I want to make sure it is effective.

Jessica Parnelli Fawkes - 回复

nice¡¡¡¡¡¡¡¡¡¡¡¡¡¡

RIGO NOLASCO - 回复

Thanks! Wii Quarantine’n in 2021!

Daniel Thomas - 回复

添加评论

浏览统计数据:

过去 24 小时: 6

过去 7 天: 43

过去 30 天: 252

总计 42,553