跳转到主内容

简介

Is your stylus stuck? We're here to help.

  1. Remove the two Phillips screws securing the battery cover to the back of the handheld console. Lift the battery cover off the back of the DSi XL.
    • Remove the two Phillips screws securing the battery cover to the back of the handheld console.

    • Lift the battery cover off the back of the DSi XL.

  2. Lift the battery from the DSi XL.
    • Lift the battery from the DSi XL.

  3. Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin.
    • Remove the four rubber screw covers on the lower case by prying them up with a push pin.

  4. Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
    • Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:

    • Four silver 5.3 mm screws

    • Two black 5.3 mm screws

    • One black 2.5 mm screw

  5. Turn the DSi XL over, and open the display. Insert a spudger between the upper and lower case at the bottom left corner of the DSi. Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.
    • Turn the DSi XL over, and open the display.

    • Insert a spudger between the upper and lower case at the bottom left corner of the DSi.

    • Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.

  6. Close the display and turn the DSi XL over. Lift the lower case from the front edge.
    • Close the display and turn the DSi XL over.

    • Lift the lower case from the front edge.

    • Rotate the lower case away from the DSi.

    • The lower case cannot be completely removed yet, since it is still connected to the motherboard.

  7. Using a spudger, pry the SD card/right shoulder button connector off its socket. Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
    • Using a spudger, pry the SD card/right shoulder button connector off its socket.

    • Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.

  8. Remove the two gold 4.0 mm Phillips screws securing the right shoulder button assembly to the back case. Lift the right shoulder button assembly from the back case. The components of the right shoulder button assembly:
    • Remove the two gold 4.0 mm Phillips screws securing the right shoulder button assembly to the back case.

    • Lift the right shoulder button assembly from the back case.

    • The components of the right shoulder button assembly:

    • Right shoulder button

    • Shoulder button spring

    • Retaining pin

    • Right shoulder button holding panel

  9. Remove the stylus from its housing on the right side of the DSi XL.
    • Remove the stylus from its housing on the right side of the DSi XL.

  10. Remove the three 4 mm gold Phillips screws securing the stylus housing to the lower case. Using a spudger, lift the stylus housing off the lower case. Remove the stylus housing from the handheld console.
    • Remove the three 4 mm gold Phillips screws securing the stylus housing to the lower case.

    • Using a spudger, lift the stylus housing off the lower case.

    • Remove the stylus housing from the handheld console.

结论

To reassemble your device, follow these instructions in reverse order.

2等其他人完成本指南。

Brett Hartt

于2010年04月12日注册

113,696 信誉积分

创作了143篇指南

团队

iFixit iFixit 的会员

Community

104 名成员

创作了9,251篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 8

总计 6,379