跳转到主内容

Nikon D7100 LCD Screen Replacement

你所需要的

  1. Nikon D7100 LCD Screen Replacement, LCD Screen: 步骤 1 中的图像 1,1
    • Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.

  2. Nikon D7100 LCD Screen Replacement: 步骤 2 中的图像 1,1
    • Remove the 3 screws under the battery flap and remove the bottom cover.

  3. Nikon D7100 LCD Screen Replacement: 步骤 3 中的图像 1,1
    • Remove the 2 screws inside the camera on the back corners.

  4. Nikon D7100 LCD Screen Replacement: 步骤 4 中的图像 1,1
    • Open the HDMI flap and remove the 2 screws.

  5. Nikon D7100 LCD Screen Replacement: 步骤 5 中的图像 1,1
    • Remove the screw next to the camera strap loop.

  6. Nikon D7100 LCD Screen Replacement: 步骤 6 中的图像 1,1
    • Remove the 2 screws on each side of the view finder.

  7. Nikon D7100 LCD Screen Replacement: 步骤 7 中的图像 1,1
    • Remove the 2 screws above and below the SD card flap.

  8. Nikon D7100 LCD Screen Replacement: 步骤 8 中的图像 1,1
    • Peel off the adhesive leather screw cover and remove the 2 screws under it.

  9. Nikon D7100 LCD Screen Replacement: 步骤 9 中的图像 1,2 Nikon D7100 LCD Screen Replacement: 步骤 9 中的图像 2,2
    • Remove the Diopter adjustment control sticker and remove the screw under it.

  10. Nikon D7100 LCD Screen Replacement: 步骤 10 中的图像 1,1
    • Separate the back panel of the camera from the actual camera.

    • Be careful not to tear any of the ribbon cables.

  11. Nikon D7100 LCD Screen Replacement: 步骤 11 中的图像 1,1
    • Disconnect the LCD ribbon cables and power cable from the motherboard.

  12. Nikon D7100 LCD Screen Replacement: 步骤 12 中的图像 1,2 Nikon D7100 LCD Screen Replacement: 步骤 12 中的图像 2,2
    • Unscrew all 16 screws around the back plate of the camera.

  13. Nikon D7100 LCD Screen Replacement: 步骤 13 中的图像 1,1
    • Then unscrew the remaining screws holding the back plate to the LCD.

    • Then simply remove the plate with the LCD.

结论

To reassemble your device, follow these instructions in reverse order.

11等其他人完成本指南。

Wesley Eveld

于02/20/18注册

731 声望

创作了4篇指南

团队

USF Tampa, Team S11-G6, Cheng Spring 2018 USF Tampa, Team S11-G6, Cheng Spring 2018 的会员

USFT-CHENG-S18S11G6

4 名成员

创作了5篇指南

9条评论

I DID IT! A couple notes: 1) You don’t need to disconnect the ribbon cables from the body. I’m new to fine electronics repair like this and I didn’t want to mess around with more cables than necessary. 2) My body doesn’t have a plastic cover over the LCD (probably why it broke…) and as such I had to reallllly pry it off. 3) Learn how to reconnect ribbon cables - I had no idea.

Patrick O'Hare - 回复

Are all screws the same size ?

trevee359 - 回复

A couple of points. This is listed as a LCD display replacement. Says only said to buy tools… Need the LCD screen as well. No idea of cost or a link to buy same. Also, you do not show removing the screen and remounting. I appreciate all the instructions on screws, but do not feel this was complete. Thanks for your instructions to this point.

Carl Bryant II - 回复

That’s very easy guide to understand. I hope to see a full guide for the Nikon D7200. thank you http://www.nikonbundle.com/nikon-d7200-b...

Deve Marko - 回复

My replacement screen cost about £44 gbp pounds from China on Ebay. The main ribbon cable is released by flipping up the thin dark grey strip opposite the ribbon using a finger nail or plastic tool on the socket then you just gently pull the cable out, the thin cable is wee bit different, using a small screw driver or dentist tool just unclip and pull/push it down towards the thin ribbon cable then slide ribbon out. When all done clean the screen on the camera and fit a thin glass protector from JJC on ebay to give more protection.

a.brown.1 - 回复

添加评论

浏览统计数据:

过去 24 小时: 3

过去 7 天: 13

过去 30 天: 61

总计 7,217