配件

无需配件。

  1. Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.
    • Remove the five screws on the bottom of the camera with a JIS #000 head screwdriver.

  2. Remove the 3 screws under the battery flap and remove the bottom cover.
    • Remove the 3 screws under the battery flap and remove the bottom cover.

  3. Remove the 2 screws inside the camera on the back corners.
    • Remove the 2 screws inside the camera on the back corners.

  4. Open the HDMI flap and remove the 2 screws.
    • Open the HDMI flap and remove the 2 screws.

  5. Remove the screw next to the camera strap loop.
    • Remove the screw next to the camera strap loop.

  6. Remove the 2 screws on each side of the view finder.
    • Remove the 2 screws on each side of the view finder.

  7. 所有超过US$100或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店
  8. Remove the 2 screws above and below the SD card flap.
    • Remove the 2 screws above and below the SD card flap.

  9. Peel off the adhesive leather screw cover and  remove the 2 screws under it.
    • Peel off the adhesive leather screw cover and remove the 2 screws under it.

  10. Remove the Diopter adjustment control sticker and remove the screw under it. Remove the Diopter adjustment control sticker and remove the screw under it.
    • Remove the Diopter adjustment control sticker and remove the screw under it.

  11. Separate the back panel of the camera from the actual camera.
    • Separate the back panel of the camera from the actual camera.

    • Be careful not to tear any of the ribbon cables.

  12. Disconnect the LCD ribbon cables and power cable from the motherboard.
    • Disconnect the LCD ribbon cables and power cable from the motherboard.

  13. Unscrew all 16 screws around the back plate of the camera. Unscrew all 16 screws around the back plate of the camera.
    • Unscrew all 16 screws around the back plate of the camera.

  14. Then unscrew the remaining screws holding the back plate to the LCD.
    • Then unscrew the remaining screws holding the back plate to the LCD.

    • Then simply remove the plate with the LCD.

  15. Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.
    • Undo the 5 ribbon cable connectors by flipping the latches up with a plastic spudger.

  16. Remove the black 4 pin connector by pulling it out of the connector.
    • Remove the black 4 pin connector by pulling it out of the connector.

  17. Remove the 7 screws holding the motherboard in place.
    • Remove the 7 screws holding the motherboard in place.

  18. This is what you should see after removing the motherboard.
    • This is what you should see after removing the motherboard.

  19. After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.
    • After following the guide to remove the back LCD screen from the motherboard, remove the 2 marked screws.

结论

To reassemble your device, follow these instructions in reverse order.

Wesley Eveld

于2018年02月20日注册

591 信誉积分

创作了4篇指南

团队

USF Tampa, Team S11-G6, Cheng Spring 2018 USF Tampa, Team S11-G6, Cheng Spring 2018 的会员

USFT-CHENG-S18S11G6

4 名成员

创作了5篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 4

过去的30天: 20

总计 233