修复你的物品 社区 商店

Nikon Coolpix S3100 Camera LCD Screen Replacement

简介

When you are in a situation whether your LCD screen is malfunctioning, this guide will assist you to find the problem.

你所需要的

  1. Nikon Coolpix S3100 Camera LCD Screen Replacement, Nikon Coolpix S3100 disassembly: 步骤 1 中的图像 1，3 Nikon Coolpix S3100 Camera LCD Screen Replacement, Nikon Coolpix S3100 disassembly: 步骤 1 中的图像 2，3 Nikon Coolpix S3100 Camera LCD Screen Replacement, Nikon Coolpix S3100 disassembly: 步骤 1 中的图像 3，3

    • Remove 8-2.46 mm screws from both sides and bottom of camera using a #000 Phillips screwdriver.

    • Remove 2 screws from left side. (picture 1)

    • Remove 4 screws from bottom. (picture 2)

    • Remove 2 screws from right side. (picture 3)

    编辑

  2. Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 2 中的图像 1，2 Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 2 中的图像 2，2

    • Remove black cover pulling up with left thumb. Hold silver cover with right thumb.

    • Remove silver cover lifting up with left thumb. Hold the camera with right thumb.

    • Once internal circuit board is exposed, the red and blue wire terminals at top center can provide a nasty shock from the charged flash capacitor (silver can to left of terminals). BE CAREFUL!

    编辑

  3. Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 3 中的图像 1，2 Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 3 中的图像 2，2

    • Remove 2-2.10mm screws in the front of the camera using a #000 Phillips screwdriver.

    • Remove the two screws.

    • Gently pull up to detach the frame. (picture 2)

    编辑

  5. Nikon Coolpix S3100 Camera LCD Screen Replacement, LCD Screen: 步骤 4 中的图像 1，1

    • Remove 2-2.10mm screws using a #000 Phillips screwdriver.

    编辑

  6. Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 5 中的图像 1，1

    • Gently pull the orange board to the right.

    编辑

  7. Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 6 中的图像 1，1

    • Lift screen up holding both corners.

    编辑

  8. Nikon Coolpix S3100 Camera LCD Screen Replacement: 步骤 7 中的图像 1，1

    • Gently pull to the left to release from ZIF connector.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

作者

与2其他贡献者

Jorge

于03/11/15注册

1,170 声望

创作了7篇指南

徽章: 13

+ 10更多徽章

团队

Colorado Springs, Team 2-4, Panko Spring 2015 Colorado Springs, Team 2-4, Panko Spring 2015 的会员

UCCS-PANKO-S15S2G4

2 名成员

创作了13篇指南

4条评论

No mention of getting an electric shock while removing the case.Bit of a tingle anyway.I held the camera in a plastic bag after that.

Sindento 1 - 回复

This will probably not be replied to, but is there any reliable way to discharge the flash capacitor? Got shocked once, but I thought it was already discharged lol.

Anirban Bhattacharyya - 回复

Connect a 1k ohm resister between the black and red wire from the capacitor. Give it a few moments to discharge through the resistor. Don't discharge the capacitor without a resistor as you run a good chance of destroying the electronics. Wear your latex gloves too.

gary.grant - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 4

过去 30 天： 11

总计 2,334