跳转到主内容

当前版本的文档还未经巡查,您可以查看最新的已查核版本

你所需要的

  1. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 1 中的图像 1,2 : 步骤 1 中的图像 2,2
    • Power off the device by holding the power button until the "Power Off" popup appears. Tap the popup and wait for the device to turn off.

    • Insert a SIM card eject tool or a paper clip into the hole next to the SIM card slot, which is located just under the power button. Do not force the paper clip if it is too thick; instead use the head of a sewing needle.

    • Push the tool into the hole until you see the card pop out.

  2. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 2 中的图像 1,1
    • Gently remove the SIM card with your fingers, or a pair of tweezers if the SIM holder does not fully eject.

    • Make sure the chip is facing the rear of the phone when reinserting the SIM card.

  3. , 后盖: 步骤 3 中的图像 1,3 , 后盖: 步骤 3 中的图像 2,3 , 后盖: 步骤 3 中的图像 3,3
    在这个步骤中使用的工具:
    iFixit Opening Picks (Set of 6)
    $4.99
    购买
    • 用塑料撬棒来解开后盖顶部与侧边的卡扣。

    • 底部由海绵胶带固定于机身。完成前述步骤后,可使用三角撬片来最终取下后盖。

    • 因 SIM 卡插槽处的塑料非常薄,容易在拆解时断裂,请避免在 SIM 卡插槽附近撬开后盖。

  4. , 中框: 步骤 4 中的图像 1,1
    • 取下 6 个固定中框的4.0 mm 菲利普斯#00 号 螺丝。

  5. : 步骤 5 中的图像 1,2 : 步骤 5 中的图像 2,2
    • 拆下中框。

  6. , 电池: 步骤 6 中的图像 1,2 , 电池: 步骤 6 中的图像 2,2
    在这个步骤中使用的工具:
    Spudger
    $2.99
    购买
    • 使用撬棒平头那端来挑起电池接线。

  7. : 步骤 7 中的图像 1,2 : 步骤 7 中的图像 2,2
    • 使用撬棒平头来断开子板的排线,把它与电池剥离。

  8. : 步骤 8 中的图像 1,3 : 步骤 8 中的图像 2,3 : 步骤 8 中的图像 3,3
    • 用塑料撬棒撬起电池。

    • 电池背面有胶用于固定,挑起时可能需要使用加热枪对胶稍稍加热。

    • 请勿刺破或弯折电池

  9. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 9 中的图像 1,2 : 步骤 9 中的图像 2,2
    • Use the flat end of a spudger to disconnect the left antenna cable.

  10. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 10 中的图像 1,2 : 步骤 10 中的图像 2,2
    • Use the flat end of a spudger to disconnect the right antenna cable.

    • These must be firmly secured during reassembly. Failure to secure the antenna connections will affect your reception and call quality.

  11. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 11 中的图像 1,2 : 步骤 11 中的图像 2,2
    • Use the flat end of a spudger to disconnect the ribbon cable that connects rear-facing camera to the motherboard.

  12. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 12 中的图像 1,2 : 步骤 12 中的图像 2,2
    • Use the flat end of a spudger to disconnect the front camera ribbon cable.

  13. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 13 中的图像 1,2 : 步骤 13 中的图像 2,2
    • Gently lift the motherboard up and out of the device.

  14. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 14 中的图像 1,3 : 步骤 14 中的图像 2,3 : 步骤 14 中的图像 3,3
    • Insert a spudger into an opening between the daughterboard and plastic housing.

    • Lift the daughterboard cover up and off the frame.

    • If Jeff, Max, Cole, Corey, Guy, Leslie, Harry, or Matt were already here, consider searching your device for surveillance bugs.

  15. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 15 中的图像 1,3 : 步骤 15 中的图像 2,3 : 步骤 15 中的图像 3,3
    • Use the flat end of a nylon spudger to pry the white and black antenna connectors up off the daughterboard.

    • These must be firmly secured during reassembly. Failure to secure the antenna connections will affect your reception and call quality.

  16. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 16 中的图像 1,2 : 步骤 16 中的图像 2,2
    • Use the flat end of a nylon spudger to pry the digitizer ZIF connector up off the daughterboard.

  17. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 17 中的图像 1,3 : 步骤 17 中的图像 2,3 : 步骤 17 中的图像 3,3
    • Insert a nylon spudger into an opening beneath the daughterboard and pry it up to free it from the frame.

    • The frame around the micro-USB port is very fragile—take care not to break this small plastic bridge.

    • Do not disconnect the daughterboard entirely. Gently fold it to the side of the phone.

  18. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 18 中的图像 1,1
    • Use an iOpener or heat gun and carefully apply heat to the digitizer panel to soften the adhesive that secures it to the frame.

    • Hold the heat gun approximately 8-10 inches from the device and apply heat in a gentle back-and-forth motion.

  19. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 19 中的图像 1,2 : 步骤 19 中的图像 2,2
    • Work the flat end of a nylon spudger under the digitizer panel. Gently pry the panel up to free it from the adhesive.

    • The phone may be too hot to touch from the heat gun. Allow a moment for it to cool to avoid burning your fingers.

  20. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 20 中的图像 1,2 : 步骤 20 中的图像 2,2
    • Use a heat gun or an iOpener to soften the adhesive along the edges of the screen.

  21. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 21 中的图像 1,2 : 步骤 21 中的图像 2,2
    • Use a suction cup to firmly pull the screen away from the frame.

    • The Nexus 5 has a very thin layer of adhesive. This should not require excessive force. Apply additional heat as needed to soften the screen adhesive.

  22. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 22 中的图像 1,2 : 步骤 22 中的图像 2,2
    • Insert an opening pick in the gap between the screen and the frame.

    • Work the opening pick along the edges of the screen to break any remaining adhesive and free the screen assembly.

  23. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 23 中的图像 1,3 : 步骤 23 中的图像 2,3 : 步骤 23 中的图像 3,3
    • Gently remove the LCD screen and digitizer assembly.

    • Carefully feed the digitizer ribbon cable through the frame.

终点

44等其他人完成本指南。

Richard

于02/07/17注册

29,761 声望

创作了11篇指南

团队

iFixit iFixit 的会员

Staff

136 名成员

创作了16,579篇指南

10条评论

This is a nice guide to understand how to disassemble and assemble your Nexus 5. 95% can be done with this guide.

Tip: read the comments!

My own tips are:

1) Search for instructions how to use glue or double sided adhesive tape. It's a must if you want succesfully put everything back together

2) You need to transfer the speaker protection from the inside of the glass to the new glass

3) The same needs to be done with with a white rectangle. It has something to do with your LED-light at the bottom.

Saw these tips in this YouTube video https://youtu.be/jQS618ayL5w

Jeroen Meyer - 回复

Thanks for the extra tips, Jeroen! These two steps can be found at 2:50 of the video for those who want to skip right to it. ;)

We do supply the tape as well: Tesa 61395 Tape

By the way, does the guy in this video remind anyone else of Thrawn from Star Wars Rebels (aka Lars Mikkelsen?)

Richard -

Hey, what size do I need for the tape? Is the mm size referring to width or thickness?

I assume it’s width and I need 1mm or 2mm to repair my Nexus 5, but which one?

Carsten Pfeifer -

I need a little help with this tutorial. I’ve bought a second hand N5 where someone replaced the screen, now the display lifts off slightly in the bottom left corner of the device. Pushing it back will only hold it in for a few minutes. Should I slide a tiny piece of double-sided adhesive tape underneath, or rather some modelmaking glue?

Ste Se - 回复

The new screen is not adhered as the old one was.. not sure what I would use for that. Not terribly important for me since it sits 99% flush, and lives in an enclosed case, but the guide should probably mention this.

Kristen McWilliam - 回复

添加评论

浏览统计数据:

过去 24 小时: 4

过去 7 天: 17

过去 30 天: 57

总计 34,867