跳转到主内容

简介

This guide will show how to remove the barrel from the blaster. A good test to check if the barrel is stuck is shown in Step 6 (we suggest to do this before opening the blaster).

配件

没有特定配件。

  1. Lay the Nerf Strongarm on its side, left side facing up. Lay the Nerf Strongarm on its side, left side facing up.
    • Lay the Nerf Strongarm on its side, left side facing up.

  2. Locate the 12 Philips head screws and remove them:  Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm Locate the 12 Philips head screws and remove them:  Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm
    • Locate the 12 Philips head screws and remove them: Head Diameter= 4.3mm, Thread Pitch= 1mm, Screw Length= 8mm

  3. Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.
    • Before removing the cover, make sure to first remove the cover for the cocking mechanism. The top half is freely removable.

    • The other half of the cocking mechanism is connected with a spring which may slide off the blaster. Be advised this is normal but worth watching to avoid damaging the spring.

  4. At this time, remove the blaster cover to reveal its internals.
    • At this time, remove the blaster cover to reveal its internals.

    • If the blaster is resting on its side, the barrel may shift slightly as it is leaning on itself (seen in the image). This is normal but should be handled with care to keep the blaster together.

  5. PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物

    PC 笔记本电池

    An easy fix for a big power boost.

    现在开始购物
  6. Once the screws have been removed, lift the top half of the gun off.
    • Once the screws have been removed, lift the top half of the gun off.

    • Notice, the gray colored piece must be removed first in order for the larger half to be removed.

    • Take care and try not to lose any smaller pieces as you open it up.

    • Locking tab for attachments.

  7. Start by inspecting the barrel closer for broken components.
    • Start by inspecting the barrel closer for broken components.

    • Pressing the unloading button is a good test to check if the barrel will rotate out.

    • If the barrel fails to cooperate, continue onto the next steps.

  8. Once the cover is off, the barrel component will be free and removable.
    • Once the cover is off, the barrel component will be free and removable.

  9. Once the barrel is removed, continue by removing the front shaft. This component is also independent of the blaster and does not require tools.
    • Once the barrel is removed, continue by removing the front shaft. This component is also independent of the blaster and does not require tools.

  10. Look for any signs of debris or any damaged locations that may be causing the barrel to lock.
    • Look for any signs of debris or any damaged locations that may be causing the barrel to lock.

  11. At this time, all components interacting with the barrel are removed.
    • At this time, all components interacting with the barrel are removed.

    • Take this time to inspect the barrel for any signs of debris or damaged locations.

结论

To reassemble your device, follow these instructions in reverse order.

8等其他人完成本指南。

Alexander Kim

于2015年08月27日注册

718 信誉积分

创作了3篇指南

团队

USF Tampa, Team 5-4, Blackwell Fall 2015 USF Tampa, Team 5-4, Blackwell Fall 2015 的会员

USFT-BLACKWELL-F15S5G4

4 名成员

创作了10篇指南

hi my barrel keeps ritating and is not fixed and does not stay aligned to the shooting point what shall i do

cryo17 - 回复

添加评论

浏览统计数据:

过去的24小时: 5

过去的7天: 19

过去的30天: 90

总计 7,686