修复你的物品 社区 商店

Neato BOTVAC CONNECTED Side Brush Replacement

简介

In this guide you will be able to replace the side brush of the Neato Botvac Connected. Replacing the side brush would be necessary if its not spinning properly. This could also be replaced if there are excess debris stuck in the brush. As a precaution make sure to disconnect the battery before beginning this guide.

你所需要的

  1. Neato BOTVAC CONNECTED Side Brush Replacement, Battery: 步骤 1 中的图像 1，1

    • Place the top of the Neato Botvac Connected against a flat surface.

    编辑

  2. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 2 中的图像 1，2 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 2 中的图像 2，2

    • Remove the two 5.5 mm screws with a Phillips #2 screwdriver.

    编辑

  3. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 3 中的图像 1，2 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 3 中的图像 2，2

    • Using the spudger, remove the panel covering the battery.

    编辑

  4. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 4 中的图像 1，3 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 4 中的图像 2，3 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 4 中的图像 3，3

    • Gently remove the connecting wires attached to the battery.

    • The wires are attached to the vacuum through a clip.

    编辑

  5. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 5 中的图像 1，1

    • Using the spudger, gently remove the battery from the device.

    编辑

  7. Neato BOTVAC CONNECTED Side Brush Replacement, Front Roller Brush: 步骤 6 中的图像 1，2 Neato BOTVAC CONNECTED Side Brush Replacement, Front Roller Brush: 步骤 6 中的图像 2，2

    • Remove the following screws with a Torx screwdriver:

    • Four 2.3 mm screws.

    编辑

  8. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 7 中的图像 1，1

    • Gently remove the thin panel held by the four screws with a spudger.

    编辑

  9. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 8 中的图像 1，1

    • Gently remove the two small wheels, and the axles attached to them.

    编辑

  10. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 9 中的图像 1，1

    • Gently remove the panel that is on top of the front roller with the spudger.

    编辑

  11. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 10 中的图像 1，1

    • Gently remove the front brush.

    编辑

  12. Neato BOTVAC CONNECTED Side Brush Replacement, Side Brush: 步骤 11 中的图像 1，2 Neato BOTVAC CONNECTED Side Brush Replacement, Side Brush: 步骤 11 中的图像 2，2

    • Gently twist the side brush back and forth.

    编辑

  13. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 12 中的图像 1，3 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 12 中的图像 2，3 Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 12 中的图像 3，3

    • Spin the side brush counter counterclockwise.

    编辑

  14. Neato BOTVAC CONNECTED Side Brush Replacement: 步骤 13 中的图像 1，1

    • Use the spudger to gently pry up and remove the side brush.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Justin Silva

于03/20/23注册

645 声望

创作了5篇指南

徽章: 5

+ 2更多徽章

团队

UMass Dartmouth, Team 6-3, Botvin Spring 2023 UMass Dartmouth, Team 6-3, Botvin Spring 2023 的会员

UMASSD-BOTVIN-S23S6G3

4 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 7

总计 142