修复你的物品 社区 商店

Motorola MBP667CONNECT Speaker Replacement

简介

This guide will show users how to take apart the camera housing in order to replace the speaker.

你所需要的

  1. Motorola MBP667CONNECT Speaker Replacement, Camera Stand: 步骤 1 中的图像 1，2 Motorola MBP667CONNECT Speaker Replacement, Camera Stand: 步骤 1 中的图像 2，2

    • Remove two 5 mm Phillips #1 screws from the bottom of the camera stand.

    编辑

  2. Motorola MBP667CONNECT Speaker Replacement: 步骤 2 中的图像 1，1

    • Use a nylon spudger to remove the casing.

    编辑

  3. Motorola MBP667CONNECT Speaker Replacement: 步骤 3 中的图像 1，1

    • Remove the two 5 mm Phillips #1 screws attached to the black plastic under the casing.

    编辑

  5. Motorola MBP667CONNECT Speaker Replacement: 步骤 4 中的图像 1，2 Motorola MBP667CONNECT Speaker Replacement: 步骤 4 中的图像 2，2

    • Remove the black circular plastic part.

    编辑

  6. Motorola MBP667CONNECT Speaker Replacement: 步骤 5 中的图像 1，1

    • Remove the white plastic wire housing beneath the black plastic.

    编辑

  7. Motorola MBP667CONNECT Speaker Replacement: 步骤 6 中的图像 1，2 Motorola MBP667CONNECT Speaker Replacement: 步骤 6 中的图像 2，2

    • Now, remove the bottom of the stand by pulling it from the camera.

    编辑

  8. Motorola MBP667CONNECT Speaker Replacement, Speaker: 步骤 7 中的图像 1，3 Motorola MBP667CONNECT Speaker Replacement, Speaker: 步骤 7 中的图像 2，3 Motorola MBP667CONNECT Speaker Replacement, Speaker: 步骤 7 中的图像 3，3

    • Remove the Phillips #1 screws on the back of the device.

    • Use a nylon spudger to remove the casing. This will separate the frontside of the camera from the backside.

    编辑

  9. Motorola MBP667CONNECT Speaker Replacement: 步骤 8 中的图像 1，2 Motorola MBP667CONNECT Speaker Replacement: 步骤 8 中的图像 2，2

    • Now locate the brackets by the speaker on the frontside of the camera and use the metal spudger to carefully disconnect from casing.

    • Continue to use the metal spudger to carefully disconnect the remaining brackets from the casing.

    编辑

  10. Motorola MBP667CONNECT Speaker Replacement: 步骤 9 中的图像 1，2 Motorola MBP667CONNECT Speaker Replacement: 步骤 9 中的图像 2，2

    • Using the soldering iron, desolder the speaker wires that are attached to the circuit board.

    • Use caution while handling the soldering iron. This tool gets very hot!

    • After desoldering the speaker wires, remove the wires from the circuit board.

    • Thread the wires from the new speaker wires through the holes in the circuit board. Using the soldering iron, re-solder the wires to the circuit board.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与4其他贡献者

Kyle Kramer

于01/16/19注册

255 声望

创作了2篇指南

徽章: 2

团队

Eastern Washington University, Team S1-G6, Crawford Winter 2019 Eastern Washington University, Team S1-G6, Crawford Winter 2019 的会员

EWU-CRAWFORD-W19S1G6

4 名成员

创作了4篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 8

总计 179