跳转到主内容

简介

This guide will show you how to replace the motherboard, as yours may be malfunctioning. This is one of the longer processes so be patient. Tools are required. There are quite a few screws in this process so be sure to not lose any, and remember which ones came from where.

  1. Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery.
    • Slide the plastic case off of the back of the phone, exposing the battery.

  2. Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone.
    • Pull up on the red battery release tab and pull the battery out of the phone.

  3. Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length. Be careful to not strip any screws.
    • Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length.

    • Be careful to not strip any screws.

  4. Using a prying tool, snap off the front casing on the top and bottom of the phone. Be careful not to lose the small rubber piece that sits over the microphone. Be careful not to lose the small rubber piece that sits over the microphone.
    • Using a prying tool, snap off the front casing on the top and bottom of the phone.

    • Be careful not to lose the small rubber piece that sits over the microphone.

  5. Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length. Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.
    • Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.

  6. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.
    • Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.

  7. Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera.
    • Using tweezers, remove the white wire at the top of the phone near the camera.

  8. Remove these nine screws using a T-3 torques. These screws should be 2.40 mm in length Remove these nine screws using a T-3 torques. These screws should be 2.40 mm in length
    • Remove these nine screws using a T-3 torques. These screws should be 2.40 mm in length

  9. Using tweezers, removed the white electrical tape on the motherboard. Using tweezers, removed the white electrical tape on the motherboard.
    • Using tweezers, removed the white electrical tape on the motherboard.

  10. Using the plastic opening tool, lift up to remove the connector. Using the plastic opening tool, lift up to remove the connector.
    • Using the plastic opening tool, lift up to remove the connector.

  11. Using a pry tool, lift the jawbone  connector. Using a pry tool, lift the jawbone  connector.
    • Using a pry tool, lift the jawbone connector.

  12. Using tweezers, carefully disconnect the cable connector by pulling the cable out. Using tweezers, carefully disconnect the cable connector by pulling the cable out.
    • Using tweezers, carefully disconnect the cable connector by pulling the cable out.

  13. Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector.
    • Use a spudger to disconnect the cable connector.

  14. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.
    • Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.

结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

Aaron Mak

于2014年10月29日注册

658 信誉积分

创作了4篇指南

团队

UMass Dartmouth, Team 4-3, Miles Fall 2014 UMass Dartmouth, Team 4-3, Miles Fall 2014 的会员

UMASSD-MILES-F14S4G3

3 名成员

创作了4篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 2

总计 651