修复你的物品 社区 商店

Minolta QTsi Maxxum Eyelet Straps Replacement

简介

Replace your broken eyelet strap so that you can wear a strap with your Minolta QTsi Maxxum camera.

你所需要的

  1. Minolta QTsi Maxxum Eyelet Straps Replacement, Eyelet Straps: 步骤 1 中的图像 1，1

    • The battery compartment is located on the bottom panel of the camera.

    • Use a coin to open the battery compartment of the camera.

    • Twist the coin counterclockwise in order to release the latch.

    编辑

  2. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 2 中的图像 1，1

    • Once the compartment is open, grab the batteries and pull them out of the compartment.

    • There should be two batteries inside the battery compartment.

    编辑

  3. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 3 中的图像 1，1

    • With a screwdriver, remove the (7) black Phillips #00 5mm screws on the bottom of the camera.

    • The screws are located on the outer edge of the bottom panel.

    • Be careful when removing the screws from the panel because they are easy to lose.

    • Once all the screws are removed, the panel should easily come off.

    编辑

  4. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 4 中的图像 1，1

    • Once the bottom panel is removed, the one screw at the bottom of the battery compartment should be visible.

    • Remove the (1) black Phillips #00 5mm screw from the battery compartment.

    编辑

  6. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 5 中的图像 1，1

    • Press the release button on the side panel to pop open the back piece of the camera.

    编辑

  7. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 6 中的图像 1，1

    • Once the back panel is open, the chamber containing one screw should be visible.

    • Remove the (1) black Phillips #00 5mm screw inside.

    编辑

  8. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 7 中的图像 1，2 Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 7 中的图像 2，2

    • Take out the (2) Phillips #00 5mm screws on the right side panel of the camera.

    • Remove the (1) Phillips #00 5mm screw on the left side panel of the camera.

    • Remove the side panels from the camera and set them aside .

    • Be careful when removing side panels. There is a plastic piece and spring underneath the left side panel that could get lost.

    编辑

  9. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 8 中的图像 1，1

    • When looking at the back of the camera, there should be a single screw on each side of the viewfinder.

    • Remove these (2) silver Phillips #00 5mm screws from each side of the viewfinder.

    编辑

  10. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 9 中的图像 1，1

    • When looking at the top of the camera, the flash hood is visible.

    • Lift the flash hood and remove the (1) silver Phillips #00 5mm screw.

    编辑

  11. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 10 中的图像 1，2 Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 10 中的图像 2，2

    • The top panel of the camera should now be easy to pop off. If it is not, make sure that all screws listed in steps 3-9 are removed.

    • Lift the top panel away from the rest of the camera.

    • Be careful when removing the top panel because there are wires connected to it.

    编辑

  12. Minolta QTsi Maxxum Eyelet Straps Replacement: 步骤 11 中的图像 1，1

    • Once all parts of the camera are removed, both eyelet straps should be visible on the top left and right sides.

    • Unscrew the (4) black Phillips #00 5mm screws to remove each eyelet strap holder and replace them.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

作者

与3其他贡献者

Maya Van Londen

于10/10/16注册

315 声望

创作了2篇指南

徽章: 12

+ 9更多徽章

团队

Sam Houston State, Team 12-4, Blackburne Fall 2016 Sam Houston State, Team 12-4, Blackburne Fall 2016 的会员

SHSU-BLACKBURNE-F16S12G4

4 名成员

创作了5篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 5

总计 341