修复你的物品 社区 商店

Marshall Woburn Tweeter Replacement

简介

Has your Marshall Woburn been having trouble with high-pitched audio? If so, here is the guide on how to remove the two tweeters. All you need is the standard #1 Phillips Screwdriver head to remove the screws involved with this replacement.

你所需要的

  1. Marshall Woburn Tweeter Replacement, Back Panel: 步骤 1 中的图像 1，2 Marshall Woburn Tweeter Replacement, Back Panel: 步骤 1 中的图像 2，2

    • Before starting, unplug the speaker from any power source. After unplugging the device, wait around 10 minutes before starting to let the capacitor fully discharge.

    • On a flat surface, orient the device so that the front grille is facing downward.

    • Using a Phillips #1 screwdriver, remove the ten outer 28.6 mm screws marked in red.

    • Remove the eight inner 28.6 mm screws with the Phillips #1 screwdriver.

    编辑

  2. Marshall Woburn Tweeter Replacement: 步骤 2 中的图像 1，2 Marshall Woburn Tweeter Replacement: 步骤 2 中的图像 2，2

    • Lift the back input board slightly above the back panel.

    • Rotate the input board so that you can slide it into the hole in the back panel that it came from.

    • Fully slide the input board through the back panel and set it down gently inside the speaker.

    编辑

  3. Marshall Woburn Tweeter Replacement: 步骤 3 中的图像 1，1

    • Grab the panel by the large hole and lift one side until you can fit your hand under.

    • Use your hand to fully remove the back panel from the rest of the frame.

    编辑

  5. Marshall Woburn Tweeter Replacement, I/O Board: 步骤 4 中的图像 1，1

    • Disconnect the 5 wires circled in red from the back input board.

    • There may be a little resistance when pulling on the wires, but it should not require excessive force.

    编辑

  6. Marshall Woburn Tweeter Replacement: 步骤 5 中的图像 1，2 Marshall Woburn Tweeter Replacement: 步骤 5 中的图像 2，2

    • Remove the two 12.7 mm screws marked in red from the front of the back input panel with a Phillips #1 screwdriver.

    • Remove the power input from the back side of the panel.

    编辑

  7. Marshall Woburn Tweeter Replacement: 步骤 6 中的图像 1，1

    • Completely remove the I/O board and the attached plate.

    编辑

  8. Marshall Woburn Tweeter Replacement, Tweeter: 步骤 7 中的图像 1，1

    • Using a Phillips #1 screwdriver, remove the eight 15.8 mm screws attaching the tweeters to the frame.

    • Disconnect the two wires from the back of each tweeter.

    编辑

  9. Marshall Woburn Tweeter Replacement: 步骤 8 中的图像 1，1

    • Lift the tweeter from the frame to remove it.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Kenneth

于10/29/23注册

169 声望

创作了2篇指南

徽章: 3

团队

UMass Dartmouth, Team 2-4, Gulbrandsen Fall 2023 UMass Dartmouth, Team 2-4, Gulbrandsen Fall 2023 的会员

UMASSD-GULBRANDSEN-F23S2G4

3 名成员

创作了6篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 2

过去 7 天： 4

过去 30 天： 19

总计 111