菜单

你的设置

我的工作台

快速访问设备的指南，配件和论坛
我的购物车

购物车是空的

浏览我们的商店

Magellan RoadMate 1200 GPS Sensor Replacement

撰写者： Ross Light (和另外4个贡献者)
  • 评论： 5
  • 收藏 0

难度

中等

步骤

7

所需时间

建议一个时间??

节

3

标志

4

Incorrect Tools

不正确的工具

通过在图片或文字中使用正确的工具来帮助完善该指南

Member-Contributed Guide

会员贡献的指南

一位我们社区很棒的成员写出了本指南。它不是由 iFixit 工作人员管理。

Bullets!

要点符号！

更好地协调标记与要点符号的颜色和类型将有助于使本指南更清楚！

Missing Prerequisites

缺少前提条件

本指南缺少关于如何开始这些步骤的信息。请编写前提指南！

简介

A guide to accessing the GPS sensor.

工具

无需工具。

配件

无需配件。

  1. Remove 4 rubber caps covering each screw by inserting the screwdriver into the side of cap and prying back and forth. Please note: this is a tedious process, but be patient.

    • Remove 4 rubber caps covering each screw by inserting the screwdriver into the side of cap and prying back and forth.

    • Please note: this is a tedious process, but be patient.

    翻译

  2. Remove the 4 screws holding the cover in place using a Phillips #00 screwdriver.

    • Remove the 4 screws holding the cover in place using a Phillips #00 screwdriver.

    翻译

  3. Open the back cover. Lift the cover slowly and carefully; the speaker is screwed on the back cover and is connected to the circuit board.

    • Open the back cover.

    • Lift the cover slowly and carefully; the speaker is screwed on the back cover and is connected to the circuit board.

    翻译

  4. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

    善于维修，即天赋异禀。

    与 #ImAGenius 分享您的维修故事

    我们都是天才

    与 #ImAGenius 分享您的维修故事

  5. Disconnect the speaker from the terminal. When reassembling, make sure that you plug the terminal in the same way. The black wire should be on the side farthest from the battery.

    • Disconnect the speaker from the terminal.

    • When reassembling, make sure that you plug the terminal in the same way. The black wire should be on the side farthest from the battery.

    翻译

  6. Unscrew the 2 screws on either side of the board. Unscrew the 2 screws on either side of the board.

    • Unscrew the 2 screws on either side of the board.

    翻译

  7. Lift the circuit board up and disconnect the GPS connector.

    • Lift the circuit board up and disconnect the GPS connector.

    翻译

  8. Carefully flip the circuit board out so you can get to the sensor easily. Remove the tape holding the sensor to the display and take out the sensor.

    • Carefully flip the circuit board out so you can get to the sensor easily.

    • Remove the tape holding the sensor to the display and take out the sensor.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

作者

与4其他贡献者

Ross Light

于2010年04月12日注册

175 信誉积分

创作了6篇指南

徽章: 11

+ 8更多徽章

0条评论

添加一条评论
浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 0

总计 2,993