菜单

你的设置

我的工作台

快速访问设备的指南，配件和论坛
我的购物车

购物车是空的

浏览我们的商店

Mad Catz Street Fighter IV FightPad Front Case Replacement

撰写者： Eric (和另外5个贡献者)
  • 评论： 0
  • 收藏 0
  • 完成 1

难度

中等

步骤

10

所需时间

15分钟

节

5

标志

0

简介

Removing the FightPad's front case for replacing the case or front artwork.

工具

购买这些工具

配件

无需配件。

  1. Use tweezers to completely remove the sticker from the rear of controller.

    • Use tweezers to completely remove the sticker from the rear of controller.

    翻译

  2. Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    • Find the seven 8.3 mm Phillips screws on the rear of the controller and remove them.

    翻译

  3. Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases. Use the plastic opening tool to pry the two cases apart.

    • Use a plastic opening tool to separate the rear and front casing by inserting it in-between the two cases.

    • Use the plastic opening tool to pry the two cases apart.

    翻译

  4. Remove the two rubber side grips. Remove the two rubber side grips.

    • Remove the two rubber side grips.

    翻译

  5. 所有超过US$100.00或包含 Pro Tech工具包的订单免费送货!

    浏览我们的商店

  6. Locate RS-DP-LS switch. Pull upwards on the switch to remove it.

    • Locate RS-DP-LS switch.

    • Pull upwards on the switch to remove it.

    翻译

  7. Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    • Locate the four 8.3 mm Phillips screws on the circuit board and remove them.

    翻译

  8. Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board. Be careful with the wires connected to the circuit board itself as they are thin and delicate. When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    • Hold the controller cable at the area just before it meets the controller and slowly lift upwards to slide it out of its plastic slot and remove the circuit board.

    • Be careful with the wires connected to the circuit board itself as they are thin and delicate.

    • When reassembling the controller, make sure that the bottom plastic piece is fully inserted into its slot before replacing the circuit board.

    翻译

  9. Remove the six buttons one by one by gripping the back of each one and pushing on them from the front. Use tweezers to remove the rubber part of the directional pad before you try to remove the shoulder buttons.

    • Remove the six buttons one by one by gripping the back of each one and pushing on them from the front.

    • Use tweezers to remove the rubber part of the directional pad before you try to remove the shoulder buttons.

    • When reinserting the buttons make sure they are in the correct place and oriented correctly.

    翻译

  10. Remove the left and right shoulder buttons by sliding them out of their respective slots.

    • Remove the left and right shoulder buttons by sliding them out of their respective slots.

    翻译

  11. Pull the plastic piece out from the bottom of the controller. Pull the plastic piece out from the bottom of the controller.

    • Pull the plastic piece out from the bottom of the controller.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与5其他贡献者

Eric

于2012年09月26日注册

81 信誉积分

创作了3篇指南

徽章: 8

+ 5更多徽章

团队

Cal Poly, Team 1-7, Propen Fall 2012 Cal Poly, Team 1-7, Propen Fall 2012 的会员

CPSU-PROPEN-F12S1G7

4 名成员

创作了7篇指南

0条评论

添加一条评论
浏览统计数据:

过去的24小时： 0

过去的7天： 0

过去的30天： 0

总计 1,127