简介

This guide will show how to open up the PowerBook so that you may access the hard drive, and then show how to remove the hard drive.

Turn the device upside down and then locate the battery latch near the front of the device.
  • Turn the device upside down and then locate the battery latch near the front of the device.

添加评论

Slide the latch to the left to release the battery.
  • Slide the latch to the left to release the battery.

添加评论

Continue holding the latch then gently pull the battery out of the device.
  • Continue holding the latch then gently pull the battery out of the device.

  • Place the battery in a safe location.

添加评论

Locate the CD-ROM Drive latch.
  • Locate the CD-ROM Drive latch.

添加评论

Slide the latch to the right to release the CD ROM drive.
  • Slide the latch to the right to release the CD ROM drive.

添加评论

Continue holding the latch then gently pull the CD-ROM Drive out of the device.
  • Continue holding the latch then gently pull the CD-ROM Drive out of the device.

  • Place the CD ROM drive in a safe location.

添加评论

Locate the speaker cover.
  • Locate the speaker cover.

添加评论

Press firmly on each end of the speaker cover and slide it to the left.
  • Press firmly on each end of the speaker cover and slide it to the left.

I found it was easy to get a spudger over the left edge and lift it up a bit, then push the bar to the left, It pops right off after that.

Jimmy James - 回复

Gently lift the speaker cover to remove it.
  • Gently lift the speaker cover to remove it.

添加评论

Lift the keyboard up from the back using a spudger(wedge side).
  • Lift the keyboard up from the back using a spudger(wedge side).

添加评论

Gently lift the keyboard until only the ribbon cable remains attached.
  • Gently lift the keyboard until only the ribbon cable remains attached.

添加评论

Tilt the keyboard away from the screen.
  • Tilt the keyboard away from the screen.

添加评论

Locate the six screws that secure the heatsink.
  • Locate the six screws that secure the heatsink.

This is not necessary to remove the HDD. Go directly to step 20.

Kenneth DeVries - 回复

That isn't the HDD!

Dix Dox - 回复

Remove the six screws from the heatsink using the Philips #1 screwdriver.
  • Remove the six screws from the heatsink using the Philips #1 screwdriver.

添加评论

Lift the heatsink from the side closest to the laptop screen.
  • Lift the heatsink from the side closest to the laptop screen.

添加评论

Remove the heatsink.
  • Remove the heatsink.

添加评论

Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.
  • Gently pull up on the beige ribbon lock until it moves a short distance on both sides to separate the ribbon cable from the connector.

添加评论

Detach the ribbon cable.
  • Detach the ribbon cable.

添加评论

Remove the keyboard.
  • Remove the keyboard.

添加评论

Locate and identify the two screws that attach the hard drive to the computer.
  • Locate and identify the two screws that attach the hard drive to the computer.

添加评论

Remove the screws with a Phillips #0 screwdriver.
  • Remove the screws with a Phillips #0 screwdriver.

添加评论

Once the screws are removed, lift up the end of the hard drive using your finger tips.
  • Once the screws are removed, lift up the end of the hard drive using your finger tips.

添加评论

Fully lift the hard drive vertically against the side of the computer.
  • Fully lift the hard drive vertically against the side of the computer.

添加评论

Push a finger down onto the plastic strap.
  • Push a finger down onto the plastic strap.

添加评论

Remove the hard drive from the computer by pushing down on the plastic strap and pulling up on the hard drive.
  • Remove the hard drive from the computer by pushing down on the plastic strap and pulling up on the hard drive.

添加评论

The hard drive is now separated from the computer.
  • The hard drive is now separated from the computer.

添加评论

  • Reverse these instructions to install a new hard drive, or to put the computer back together.

添加评论

结论

To reassemble your device, follow these instructions in reverse order.

5等其他人完成本指南。

Jeffrey Huntley

于2011年04月01日注册

122 信誉积分

撰写一个指南

团队

Cal Poly, Team 10-39, Forte Spring 2011 Cal Poly, Team 10-39, Forte Spring 2011 的会员

CPSU-FORTE-S11S10G39

5 名成员

创作了6篇指南

Hi iFixIt thanks for all the details BUT the keyboard can indeed stay in

when changing the hard drive. Just slide it a bit to the right after step

11, the ribbon cble does not take any damage. SO: from step 12 jump

straight to step 20. The heat sink can stay untouched, which i find not

unimportant to mention. Regards, TB75

TB75 - 回复

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 8

过去的30天: 44

总计 5,679