简介

移除保护板上的几颗螺丝来让您能够更换RAM

  1. 使用手来推动电池上的电池释放开关,然后将电池从电脑上移走。
    • 使用手来推动电池上的电池释放开关,然后将电池从电脑上移走。

    添加评论

  2. Free shipping on orders over $20
    Use code BLUEANDBLACK at checkout
    Free shipping on orders over $20
    Use code BLUEANDBLACK
  3. 移除三颗相同的 Phillips螺丝。
    • 移除三颗相同的 Phillips螺丝。

    Tip for new players - print this guide, then use Sello tape to tape the screws from each step on the picture. Keeps them all organised and easy to know which screws belong to which step when putting it all back together

    MPB Monkey - 回复

    Thanks a lot for this great advice. I followed it, and it turned out to be very useful and practical.

    Ralf Bergs -

    来自 MPB Monkey 的话:

    "...Tip for new players - print this guide, then use Sello tape..."

    It's one word: Sellotape, the biggest brand in Europe. :-)

    matthk - 回复

    In regard to the incredible amount of TINY screws, get an Ice Cube Tray or something with AT LEAST 8 compartments, then, when taking out the screws, mark EACH compartment with the step # and how many screws that were taken out, and used for THAT STEP (such as Step # 3 = 4 of 4 screws. Label EACH compartment, and keep them in line of each step. When it comes time to put everything back together, just reverse your Ice Cube Tray, and follow the Steps in Reverse!

    As far as marking each compartment, try these POST IT PENS!!!

    http://www.staples.com/Post-it-Flag-Ball...

    GOOD LUCK! Take your time, it's not as difficult as it seems!

    JerseyJeepGurl

    JerseyJeepGurl - 回复

    An ice cube tray is definitely the way to go!

    Martok Bulls -

    This guide helped me to remove the keyboard on my MBP, but it doesn't take you further to take the keyboard apart. If you REALLY want to look inside the keyboard, you'll need to remove additional phillips screws (10), and carefully remove the inner plastic/clear layers inside the keyboard.

    I did this to look for physical damage inside the keyboard and noticed that the black plastic? sheet was torn on my letter 'v', which was one of the keys not working. I did not see any physical sign anywhere else on the keyboard, though.

    So, after pulling the defective keyboard away and installing the new one purchased from iFixit, putting everything back together is not too difficult, just reverse.

    One thing, though: Check and double-check before you tighten the case screws to make sure your keyboard backlight is working. I noticed I had forgotten to plug it in, luckily for me before I put all the screws on the case.

    To avoid losing any screws, print this guide and use clear tape to tape the screws next to the step. Use double-tape to avoid tearing or one of the tiny screws from falling out.

    Good luck!

    Thanks iFixit for helping me replace my MBP's keyboard!

    juanortuno - 回复

    Thank you for some excellent advice form JerseyJeep Gurl

    来自 SubodhJ 的话:

    SubodhJ - 回复

    Worked perfect on my 4,1 mbp. Took ~15 min.

    I don't see a boost in speed... or is just me?

    I used 500 GB 7200 RPM Seagate SATA Hard Drive model ST9500420AS.

    (if has a G letter at the end (ASG) is the one with built in shock protection who conflict sometimes with the mac own G protection).

    crus - 回复

    This guide was awesome. I used JerseyJeepGurl's suggestion and used an egg carton, numbering each cavity as a step in the guide. So for a step that had me remove 3 different kinds of screws, I had a cavity for each, numbered: 1a, 1b, 1c and wrote a,b,c on the guide itself next to each bullet point in the step. It was awesome.

    I guess that before starting I overlooked what a T6 torx actually was. I started this process at 8pm and realized right away that I did not have a set that small and of course all stores were closing. Lowes actually had an awesome fine torx driver set for only 7 bucks!

    So that you fixit.

    tech4eleven - 回复

    来自 tech4eleven 的话:

    This guide was awesome. I used JerseyJeepGurl's suggestion and used an egg carton, numbering each cavity as a step in the guide. So for a step that had me remove 3 different kinds of screws, I had a cavity for each, numbered: 1a, 1b, 1c and wrote a,b,c on the guide itself next to each bullet point in the step. It was awesome.

    I guess that before starting I overlooked what a T6 torx actually was. I started this process at 8pm and realized right away that I did not have a set that small and of course all stores were closing. Lowes actually had an awesome fine torx driver set for only 7 bucks!

    So that you fixit.

    Thank you everybody for "thanking me" on the compartment advice! Also, just about ANY Auto parts store will have a set of Torx Screw drivers, in a handy little set, that is all together. Good luck everybody,,remember,TAKE YOUR TIME, BREATH, AND DON'T GET FRUSTRATED!!! (STEALING ADVICE FROM PEARL JAM,,BREATH,JUST BREATH),,,,AND YOU'LL BE ABLE TO DO IT YOURSELF!

    JJG

    JerseyJeepGurl - 回复

    来自 JerseyJeepGurl 的话:

    In regard to the incredible amount of TINY screws, get an Ice Cube Tray or something with AT LEAST 8 compartments, then, when taking out the screws, mark EACH compartment with the step # and how many screws that were taken out, and used for THAT STEP (such as Step # 3 = 4 of 4 screws. Label EACH compartment, and keep them in line of each step. When it comes time to put everything back together, just reverse your Ice Cube Tray, and follow the Steps in Reverse!

    As far as marking each compartment, try these POST IT PENS!!!

    http://www.staples.com/Post-it-Flag-Ball...

    GOOD LUCK! Take your time, it's not as difficult as it seems!

    JerseyJeepGurl

    Michael Fredrickson - 回复

    来自 Michael Fredrickson 的话:

    I get a piece of "corrugated" cardboard and draw an outline of the laptop and all the "compartments" that are accessed. When you take a screw out simply punch it threw top layer of the cardboard exactly where it goes. Multiple compartments - just draw another diagram on the cardboard. Voila!

    Michael Fredrickson - 回复

    I just finished replacing my hard drive following these instructions and they were perfect. The only minor complication involved the ribbon cable connecting to the sleep light and IR sensor connectors. The entire cable was tightly glued to the hard drive. But I got it loose with 10 minutes of gentle prying with a spudger.

    To keep track of the screws I just sketched an outline of the bottom panel, taped the screws in the right places and numbered them with the step numbers.

    Tom McAuliffe - 回复

    I just used that Glad Press' N Seal. I just cut a 4 in piece, cut slits in it to about half way, Put the screws on there, and fold the pieces over the screws. You can number them, i just kept track of them. Also, you might not need that much, i just cut that much just to be safe.

    benchallinor27 - 回复

    I use magnet

    I use the magnet that close the refigerator door.

    The screws are put on the magnet, so it didnot fall from the table.

    i am french so sorry for my english

    Madoc -

    Just another idea for a container for all the little screws: pillbox. I got one for about $1.00 at the store with 14 compartments.

    Brian Littmann - 回复

    • 向上提起记忆门足高的高度来抓住它,并滑动其,将其从拉出。

    添加评论

结论

要重新组装您的设备,请按照本指南的相反顺序进行操作。

6等其他人完成本指南。

特别感谢这些译者︰

100%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

iRobot

于2009年09月24日注册

1 信誉积分

创作了621篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 4

总计 6,294