跳转到主内容
  1. 使用手来推动电池上的电池释放开关,然后将电池从电脑上移走。
    • 使用手来推动电池上的电池释放开关,然后将电池从电脑上移走。

  2. 移除三颗相同的十字螺丝。
    • 移除三颗相同的十字螺丝。

    Tip for new players - print this guide, then use Sello tape to tape the screws from each step on the picture. Keeps them all organised and easy to know which screws belong to which step when putting it all back together

    MPB Monkey - 回复

    Thanks a lot for this great advice. I followed it, and it turned out to be very useful and practical.

    Ralf Bergs -

    来自 MPB Monkey 的话:

    "...Tip for new players - print this guide, then use Sello tape..."

    It's one word: Sellotape, the biggest brand in Europe. :-)

    matthk - 回复

    In regard to the incredible amount of TINY screws, get an Ice Cube Tray or something with AT LEAST 8 compartments, then, when taking out the screws, mark EACH compartment with the step # and how many screws that were taken out, and used for THAT STEP (such as Step # 3 = 4 of 4 screws. Label EACH compartment, and keep them in line of each step. When it comes time to put everything back together, just reverse your Ice Cube Tray, and follow the Steps in Reverse!

    As far as marking each compartment, try these POST IT PENS!!!

    http://www.staples.com/Post-it-Flag-Ball...

    GOOD LUCK! Take your time, it's not as difficult as it seems!

    JerseyJeepGurl

    JerseyJeepGurl - 回复

    An ice cube tray is definitely the way to go!

    Martok Bulls -

    This guide helped me to remove the keyboard on my MBP, but it doesn't take you further to take the keyboard apart. If you REALLY want to look inside the keyboard, you'll need to remove additional phillips screws (10), and carefully remove the inner plastic/clear layers inside the keyboard.

    I did this to look for physical damage inside the keyboard and noticed that the black plastic? sheet was torn on my letter 'v', which was one of the keys not working. I did not see any physical sign anywhere else on the keyboard, though.

    So, after pulling the defective keyboard away and installing the new one purchased from iFixit, putting everything back together is not too difficult, just reverse.

    One thing, though: Check and double-check before you tighten the case screws to make sure your keyboard backlight is working. I noticed I had forgotten to plug it in, luckily for me before I put all the screws on the case.

    To avoid losing any screws, print this guide and use clear tape to tape the screws next to the step. Use double-tape to avoid tearing or one of the tiny screws from falling out.

    Good luck!

    Thanks iFixit for helping me replace my MBP's keyboard!

    juanortuno - 回复

    Thank you for some excellent advice form JerseyJeep Gurl

    来自 SubodhJ 的话:

    SubodhJ - 回复

    Worked perfect on my 4,1 mbp. Took ~15 min.

    I don't see a boost in speed... or is just me?

    I used 500 GB 7200 RPM Seagate SATA Hard Drive model ST9500420AS.

    (if has a G letter at the end (ASG) is the one with built in shock protection who conflict sometimes with the mac own G protection).

    crus - 回复

    This guide was awesome. I used JerseyJeepGurl's suggestion and used an egg carton, numbering each cavity as a step in the guide. So for a step that had me remove 3 different kinds of screws, I had a cavity for each, numbered: 1a, 1b, 1c and wrote a,b,c on the guide itself next to each bullet point in the step. It was awesome.

    I guess that before starting I overlooked what a T6 torx actually was. I started this process at 8pm and realized right away that I did not have a set that small and of course all stores were closing. Lowes actually had an awesome fine torx driver set for only 7 bucks!

    So that you fixit.

    tech4eleven - 回复

    来自 tech4eleven 的话:

    This guide was awesome. I used JerseyJeepGurl's suggestion and used an egg carton, numbering each cavity as a step in the guide. So for a step that had me remove 3 different kinds of screws, I had a cavity for each, numbered: 1a, 1b, 1c and wrote a,b,c on the guide itself next to each bullet point in the step. It was awesome.

    I guess that before starting I overlooked what a T6 torx actually was. I started this process at 8pm and realized right away that I did not have a set that small and of course all stores were closing. Lowes actually had an awesome fine torx driver set for only 7 bucks!

    So that you fixit.

    Thank you everybody for "thanking me" on the compartment advice! Also, just about ANY Auto parts store will have a set of Torx Screw drivers, in a handy little set, that is all together. Good luck everybody,,remember,TAKE YOUR TIME, BREATH, AND DON'T GET FRUSTRATED!!! (STEALING ADVICE FROM PEARL JAM,,BREATH,JUST BREATH),,,,AND YOU'LL BE ABLE TO DO IT YOURSELF!

    JJG

    JerseyJeepGurl - 回复

    来自 JerseyJeepGurl 的话:

    In regard to the incredible amount of TINY screws, get an Ice Cube Tray or something with AT LEAST 8 compartments, then, when taking out the screws, mark EACH compartment with the step # and how many screws that were taken out, and used for THAT STEP (such as Step # 3 = 4 of 4 screws. Label EACH compartment, and keep them in line of each step. When it comes time to put everything back together, just reverse your Ice Cube Tray, and follow the Steps in Reverse!

    As far as marking each compartment, try these POST IT PENS!!!

    http://www.staples.com/Post-it-Flag-Ball...

    GOOD LUCK! Take your time, it's not as difficult as it seems!

    JerseyJeepGurl

    Michael Fredrickson - 回复

    来自 Michael Fredrickson 的话:

    I get a piece of "corrugated" cardboard and draw an outline of the laptop and all the "compartments" that are accessed. When you take a screw out simply punch it threw top layer of the cardboard exactly where it goes. Multiple compartments - just draw another diagram on the cardboard. Voila!

    Michael Fredrickson - 回复

    I just finished replacing my hard drive following these instructions and they were perfect. The only minor complication involved the ribbon cable connecting to the sleep light and IR sensor connectors. The entire cable was tightly glued to the hard drive. But I got it loose with 10 minutes of gentle prying with a spudger.

    To keep track of the screws I just sketched an outline of the bottom panel, taped the screws in the right places and numbered them with the step numbers.

    Tom McAuliffe - 回复

    I just used that Glad Press' N Seal. I just cut a 4 in piece, cut slits in it to about half way, Put the screws on there, and fold the pieces over the screws. You can number them, i just kept track of them. Also, you might not need that much, i just cut that much just to be safe.

    benchallinor27 - 回复

    I use magnet

    I use the magnet that close the refigerator door.

    The screws are put on the magnet, so it didnot fall from the table.

    i am french so sorry for my english

    Madoc -

    Just another idea for a container for all the little screws: pillbox. I got one for about $1.00 at the store with 14 compartments.

    Brian Littmann - 回复

  3. 向上提起记忆门足高的高度来抓住它,并滑动其,将其从拉出。
    • 向上提起记忆门足高的高度来抓住它,并滑动其,将其从拉出。

  4. 卸下电池仓闩锁附近的两个2.8 mm Phillips螺丝。
    • 卸下电池仓闩锁附近的两个2.8 mm Phillips螺丝。

  5. 移除下列6颗螺丝
    • 移除下列6颗螺丝

    • 两个10 mm T6 Torx螺丝位于RAM插槽的两侧。

    • 四个14.5毫米十字螺丝 位于铰链附近。

  6. 移除电脑插口附近的四颗3.2 mm Phillips 螺丝。
    • 移除电脑插口附近的四颗3.2 mm Phillips 螺丝。

    "port side of the computer" should read "starboard side". It's on the right-hand side when the computer is positioned normally in front of you.

    joeycoole - 回复

    Port side as in I/O port side, as in the side that has the FireWire and ethernet ports. This is a MacBook, not a sailboat ;)

    Andrew Bookholt -

    Maybe I'm too used to running flight simulators on my Macs. But to us sailors or pilots, it would perhaps be clearer if the instructions mentioned "I/O port side" as Andrew did above.

    Honestly, it never crossed my mind that 'port' refered to in/out…

    joeycoole -

  7. 旋转90度,然后移除2颗固定电脑后壳的 3.2 mm Phillips螺丝。
    • 旋转90度,然后移除2颗固定电脑后壳的 3.2 mm Phillips螺丝。

  8. 再转90度,然后移除侧面的四颗3.2 mm Phillips螺丝。
    • 再转90度,然后移除侧面的四颗3.2 mm Phillips螺丝。

    In my machine the screw closest to the power connector had a slightly thicker head, and would not sit flush, upon reassembly, unless it was returned to the same hole.

    Martin Kenny - 回复

  9. 切勿猛拉顶壳,顶壳仍然通过排线与逻辑板相连。
    • 切勿猛拉顶壳,顶壳仍然通过排线与逻辑板相连。

    • 抬起壳子的后部,沿着两边用手指撬动,随着手的移动来撬开顶壳。 一旦松开了两侧,您可能需要上下摆动来释放上部的前部的卡扣(有一些隐藏的塑料卡扣需要“特殊照顾”)。

    Be super careful not to bend the metal tabs that hook the upper case into the lower case. If bent these make it challenging to close and reattach the upper case.

    lama - 回复

    I had already done this once and now have a larger SSD to put in and cannot get past this step as the back just will not pop off. In fact- the front comes off fine but the back, where you cannot get the spudger, is "glued" or wedged solid. I suspect that the rear screw tabs have jammed. :(

    Stefanie - 回复

    I would not rock the case up and back. There are 4 plastic connectors that need to come loose, start on the left side with a spudger about a quarter of the distance from the edge and pop them up from left to right, one by one.

    maccentric - 回复

  10. 断开触摸板以及键盘连接到逻辑板的排线。
    • 断开触摸板以及键盘连接到逻辑板的排线。

    • 移除顶壳

    Kudos for this fantastic walk-through of replacing the hard drive. I just swapped in a new SSD and it was a piece of cake!

    On Step 10, I tried just propping up the keyboard and leaving it connected to the logic board. It worked for a while but eventually the ribbon popped off. Luckily it wasn't damaged and it's super easy to replace.

    DJR - 回复

    Same happened to me. No damage here either. :-)

    Ralf Bergs -

    Since there is the ONE cable going from the top keyboard/touchpad assembly to the motherboard, you need to be careful lifting it up and removing it.

    Start at the front of the laptop, using a spudger to widen the gap so you can see inside where the ribbon cable attaches.

    When re-assembling, use a couple of spudgers to prop up the keyboard/touchpad assembly and hold it in place. Re-connect the cable, then starting from the rear, lower the assembly into place.

    ECJohansen - 回复

  11. 这个步骤还没有翻译 帮忙翻译一下

    Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.
    • Disconnect the iSight cable from the logic board by sliding the cable to the left and out of its connector.

  12. 这个步骤还没有翻译 帮忙翻译一下

    Disconnect the inverter, left fan, and left ambient light sensor cables by placing a spudger beneath each cable and lifting up.
    • Disconnect the inverter, left fan, and left ambient light sensor cables by placing a spudger beneath each cable and lifting up.

  13. 这个步骤还没有翻译 帮忙翻译一下

    Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.
    • Peel up the left ambient light sensor cable from above the left fan, removing tape as necessary.

  14. 这个步骤还没有翻译 帮忙翻译一下

    Remove the following 3 screws:
    • Remove the following 3 screws:

    • One 6.2 mm black T6 Torx screw from the right side of the fan.

    • Two 9.4 mm silver T6 Torx screws from the left side of the fan.

  15. 这个步骤还没有翻译 帮忙翻译一下

    Lift the left fan up and carefully peel up the tape securing the fan to the heat sink as you go.
    • Lift the left fan up and carefully peel up the tape securing the fan to the heat sink as you go.

终点

66等其他人完成本指南。

iRobot

于2009年09月24日注册

1 信誉积分

创作了647篇指南

6条评论

Hi Folks!

I'm a crotchety, 82 year-old geezer with big hands, and somehow or the other I managed to replace the left fan in my MacBook Pro 15" 1211 in about one hour! It was helpful to use a paper-mache egg carton to organize the little itsy-bitsy screw, because if you ever lost one you would never, ever find it again!

I had to use a big hammer occasionally to get things back together, but lo and behold my wife turned on her beloved machine and was very surprised to find that it works perfectly.

Many thanks for your great help and instructive manual!

Sincerely, Doc Botsford

mangeymooz - 回复

what a money saver and life saver. iFixit is awesome! Have to admit though you need to be fearless to open up your computer and take a chance. Be VERY careful with the connectors, and know how they are connected or they will break. The iSight cable pulls out to the left, but DONT pull on the wires. Use the spudger to wiggle out the metal tabs on the connector. Don't lift up on the connector. And the heat sink tape doesn't come off that easiy either. Once you pull the front of the fan upright so it's on it's edge, then use the spudger and go behind to pull the black tape off SLOWLY. And while you're reaching over those delicate prts, make sure you don't bang down on some resistor or other part. It's a thrill when you put it back together and you DON'T HEAR A THING! The fan is QUIET. Didn't realize how loud it was getting.

Bill - 回复

I finally got around to replacing both my fans. I had tried cleaning and putting drop of WD40 on the post of each one. They worked, but were noisy. Now I have replaced both fans and the computer is absolutely quiet(as far as I can tell) And cooler too. I went ahead and upgraded to 10.7(the highest OS it will take), so it is like I have a new computer. Thanks, ifixit

garyrclark - 回复

Looking for some HELP here, if anyone can help out.

Macbook Pro 15 2.33 had problem with defective left fan. Didn't turn on. I installed Macs Fan Control and tried to change fan speed, but it didn't show up in menu, so concluded it was broken.

I replaced it with a left fan listed as compatible with this model and with the next series, from 2007.

As soon as I booted up the computer with the replaced fan, it came on at full throttle and never slowed down. As soon as I press the power button, the left fan comes on.

So ended up with opposite problem! Left side is now very cool, but super noisy!

The install seemed to go okay, so I don't know what the problem might be. I reset SMC and PRAM, but no change.

Any ideas?

Simple Simon - 回复

Same here. Did you found a solution?

Anderson -

The replaced fan runs at fullspeed all time. What could I made wrong?

Anderson - 回复

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 1

过去的30天: 9

总计 63,791