修复你的物品

维修的权力

商店

MacBook Pro 13" Unibody Late 2011 Right Speaker/Subwoofer Replacement

撰写者： Phillip Takahashi (和另外3个贡献者)
  • 评论： 70
  • 收藏 9
  • 完成 17

难度

中等

步骤

18

所需时间

30 - 45 分钟

节

4

标志

0

简介

Use this guide to replace a blown subwoofer or right speaker.

  1. Remove the following ten screws:

    • Remove the following ten screws:

    • Three 14.4 mm Phillips #00 screws

    • Three 3.5 mm Phillips #00 screws

    • Four 3.5 mm shouldered Phillips #00 screws

    • When replacing the small screws, align them perpendicular to the slight curvature of the case (they don't go straight down).

    编辑

  2. Use your fingers to pry the lower case away from the body of the MacBook near the vent. Remove the lower case.

    • Use your fingers to pry the lower case away from the body of the MacBook near the vent.

    • Remove the lower case.

    编辑

  3. Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board. It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.

    • Use the edge of a spudger to pry the battery connector upwards from its socket on the logic board.

    • It is useful to pry upward on both short sides of the connector to "walk" it out of its socket. Be careful with the corners of the connectors, they can be easily broken off.

    编辑

  4. Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

    • Bend the battery cable slightly away from its socket on the logic board so it does not accidentally connect itself while you work.

    编辑

  5. Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up from its socket on the logic board.

    • Use the flat end of a spudger to pry the AirPort/Bluetooth ribbon cable connector up from its socket on the logic board.

    编辑

  6. Carefully pull the camera cable out of its socket on the logic board.

    • Carefully pull the camera cable out of its socket on the logic board.

    • Though not recommended by iFixit staff, some users opt to omit this step completely. For information on this, see the step comments.

    • Pull the cable parallel to the face of the logic board. Pulling it upward may damage the logic board or the cable itself.

    编辑

  8. Carefully move the AirPort/Bluetooth ribbon cable out of the way as you peel the camera cable off the adhesive securing it to the subwoofer and the AirPort/Bluetooth bracket. De-route the camera cable out from under the retaining finger molded into the AirPort/Bluetooth bracket.

    • Carefully move the AirPort/Bluetooth ribbon cable out of the way as you peel the camera cable off the adhesive securing it to the subwoofer and the AirPort/Bluetooth bracket.

    • De-route the camera cable out from under the retaining finger molded into the AirPort/Bluetooth bracket.

    编辑

  9. Use the tip of a spudger to pry the antenna connector closest to the logic board up from its socket on the AirPort/Bluetooth board. De-route the antenna cable from under the finger molded into the AirPort/Bluetooth bracket.

    • Use the tip of a spudger to pry the antenna connector closest to the logic board up from its socket on the AirPort/Bluetooth board.

    • De-route the antenna cable from under the finger molded into the AirPort/Bluetooth bracket.

    编辑

  10. Remove the following five screws:

    • Remove the following five screws:

    • Two 10.3 mm Phillips screws

    • Two 3.1 mm Phillips screws

    • One 5 mm Phillips screw

    编辑

  11. Pull the AirPort/Bluetooth assembly and the Subwoofer upward near the center of the side of the optical drive until they clear each other. Move the AirPort/Bluetooth assembly and the subwoofer away from the top of the optical drive.

    • Pull the AirPort/Bluetooth assembly and the Subwoofer upward near the center of the side of the optical drive until they clear each other.

    • Move the AirPort/Bluetooth assembly and the subwoofer away from the top of the optical drive.

    编辑

  12. Pull the right speaker/subwoofer cable out from under the retaining finger near the side of the optical drive. Pull the right speaker/subwoofer cable upward to disconnect it from the logic board.

    • Pull the right speaker/subwoofer cable out from under the retaining finger near the side of the optical drive.

    • Pull the right speaker/subwoofer cable upward to disconnect it from the logic board.

    编辑

  13. Use the flat end of a spudger to pry the hard drive cable connector up from its socket on the logic board.

    • Use the flat end of a spudger to pry the hard drive cable connector up from its socket on the logic board.

    • Bend the hard drive cable away from the optical drive.

    编辑

  14. Use the flat end of a spudger to pry the optical drive connector up from its socket on the logic board.

    • Use the flat end of a spudger to pry the optical drive connector up from its socket on the logic board.

    编辑

  15. Remove the three 2.7 mm Phillips screws securing the optical drive to the upper case.

    • Remove the three 2.7 mm Phillips screws securing the optical drive to the upper case.

    编辑

  16. Pull the optical drive upward from its edge closest to the display and remove it from the upper case.

    • Pull the optical drive upward from its edge closest to the display and remove it from the upper case.

    编辑

  17. Use a plastic opening tool or another thin prying object to carefully pry the right speaker up from the adhesive securing it to the upper case. Start prying up from the edge of the right speaker nearest the display. Starting from the other side may damage one of the antennas.

    • Use a plastic opening tool or another thin prying object to carefully pry the right speaker up from the adhesive securing it to the upper case.

    • Start prying up from the edge of the right speaker nearest the display. Starting from the other side may damage one of the antennas.

    • Pry up along the edge of the right speaker until it is separated from the upper case.

    编辑

  18. Pull the right speaker away from the optical drive opening.

    • Pull the right speaker away from the optical drive opening.

    编辑

  19. Peel up the right speaker cable along the edge of the optical drive opening. De-route the cable from the clips near the edge of the logic board.

    • Peel up the right speaker cable along the edge of the optical drive opening.

    • De-route the cable from the clips near the edge of the logic board.

    • Remove the right speaker/subwoofer assembly from the upper case.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

17等其他人完成本指南。

作者

与3其他贡献者

Phillip Takahashi

于2011年08月22日注册

82,165 信誉积分

创作了87篇指南

徽章: 43

+ 40更多徽章

3条评论

添加一条评论

Done! No troubles - thanks for the parts, iFixit!

Kit - 回复

Killer detailed instructions!! However, it’s clear to me that this is going to the shop for repair - way over my head !!! NICE job, though!!

Drew Pieros - 回复

I was bloody terrified the whole time but it worked. My audio no longer clips at certain frequencies. Also I feel like a god and my household is quote “very impressed.” Bless your soul Philip!!!!

Emily Gerren - 回复

添加评论

浏览统计数据:

过去的24小时： 16

过去的7天： 116

过去的30天： 454

总计 28,871