修复你的物品 社区 商店

MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement

仅作为前提条件
本指南仅用作其他指南的先决条件。不能单独食用。

你所需要的

  1. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: 步骤 1 中的图像 1，2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement, Trackpad Cable: 步骤 1 中的图像 2，2

    • Use the flat end of a spudger to pop the trackpad connector straight up off its socket on the logic board.

    编辑

  2. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 2 中的图像 1，2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 2 中的图像 2，2

    • Lift the trackpad cable up off the battery to separate it from the adhesive securing it.

    • Be careful not to damage the cable. If it doesn't peel up easily, apply a little heat from an iOpener, heat gun, or hair dryer to soften the adhesive, and try again.

    • If you are installing a new trackpad cable, be sure to fold the new cable to match the shape of the old cable. The new cable will appear to be too long if it is not folded.

    编辑

  4. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 3 中的图像 1，3 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 3 中的图像 2，3 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 3 中的图像 3，3

    • If necessary, peel back any tape covering the trackpad cable connector.

    • Use the end of a spudger to flip the retaining tab on the ZIF connector.

    编辑

  5. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 4 中的图像 1，2 MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 4 中的图像 2，2

    • Pull the trackpad cable straight out of its ZIF socket on the trackpad control board.

    • During reassembly, make sure that the retaining tab is in the up, "unlocked" position before you insert the cable into the socket.

    编辑

  6. MacBook Pro 13" Retina Display Early 2015 Trackpad Cable Replacement: 步骤 5 中的图像 1，1

    • Remove the single 3.7 mm T5 Torx screw securing the battery board to the upper case.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

3等其他人完成本指南。

作者

与6其他贡献者

Sam Goldheart

于10/18/12注册

465,958 声望

创作了538篇指南

徽章: 48

+ 45更多徽章

团队

iFixit iFixit 的会员

Staff

136 名成员

创作了17,298篇指南

3条评论

Why remove the screw in step 5?

Ari Cooper - Davis - 回复

Yes @sam , why should you remove the screw in step 5? Is this a mistake?

lmdehaas - 回复

Step 5: Remove the single 3.7 mm T5 Torx screw.

Step 6: Re-screw single 3.7 mm T5 Torx screw.

David Grabowski - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 2

过去 30 天： 13

总计 1,795