跳转到主内容

当前版本的文档还未经巡查,您可以查看最新的已查核版本

你所需要的

  1. , 底壳: 步骤 1 中的图像 1,1
    在这个步骤中使用的工具:
    P5 Pentalobe Screwdriver Retina MacBook Pro and Air
    $5.99
    购买
    • 在开始更换之前,关机,合上屏幕然后把机器正面朝上平放在软面上。

    • 使用P5 Pentalobe 螺丝刀将底部的十颗螺丝移除,有下面两种规格:

    • 两个9mm 梅花形螺丝

    • 八个2.6mm梅花形螺丝

  2. : 步骤 2 中的图像 1,1
    • 把手指插进显示器和底壳之间的缝隙然后向上拉,即可拆下底壳。

    • 请小心地取下底壳并放在保证安全的地方。

  3. , 电池排线: 步骤 3 中的图像 1,2 , 电池排线: 步骤 3 中的图像 2,2
    • 确保你在维修时一切都处于断电状态,请先断开电池。

    • 抓住连接到电池接口的透明塑料拉片,将其平行于电路板拉向 MacBook Air 的前缘。

    • 断开连接时请勿向上提起接口,否则可能会损坏接口插座。

  4. : 步骤 4 中的图像 1,1
    • 使用撬棒的平端撬开 在I/O 板上的延长线

  5. : 步骤 5 中的图像 1,1
    • 小心地将 I/O 板延长线从风扇上的粘合剂上剥开。

    • 在重新组装过程中,请确保此排线处于正确的方向。如果颠倒过来, 虽然能够适合, 但笔记本电脑不会启动。

  6. : 步骤 6 中的图像 1,2 : 步骤 6 中的图像 2,2
    • 以下排线座具有特别深的插座。请小心的把他断开

    • 轻轻地将 I/O 板延长线向上挑起,则使用撬棒的平端撬动排线的侧面,以帮助将其从插座中拿出来。

    • 拆下 I/O 板电缆。

  7. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 7 中的图像 1,1
    • Use the tip of a spudger to carefully flip up the retaining flap on the fan cable ZIF socket.

    • Be sure you are prying up on the hinged retaining flap, not the socket itself.

  8. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 8 中的图像 1,1
    • Peel the rubber gasket off the adhesive on the top of the fan.

  9. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 9 中的图像 1,1
    • Remove the following three screws securing the fan to the upper case:

    • One 3.6 mm T5 Torx screw

    • One 2.7 mm T5 Torx screw

    • One 3.6 mm T5 Torx screw with a short head

  10. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 10 中的图像 1,2 : 步骤 10 中的图像 2,2
    • Lift the fan from the I/O board side and pull it free from the upper case.

    • Removing the fan will also disconnect the fan ribbon cable. Be careful not to snag it.

终点

25等其他人完成本指南。

3条评论

Step 1

My mid-2013 MacBook Air requires a pentalobe P4 driver, not a pentalobe P5 driver. I got a set of P1 - P6 so it wasn't an issue for me.

Scott - 回复

Do I need the artic silver thermal paste? I know the guide does not mention it, but a repair guy I went to first included it in the quote they gave me to fix the fan ($200 for parts and work for a fan replacement)

Mary Austin Morgan - 回复

Arctic silver is a great thermal paste, but in my experience the swapping of the fans does not require any thermal paste. Thermal paste is usually used in between the connections of the computer's processor heat sink(s) and the processor, as well as the graphics card and the heat sinks.

Barrythetech -

添加评论

浏览统计数据:

过去 24 小时: 2

过去 7 天: 22

过去 30 天: 81

总计 25,677