简介

使用本指南来更换天线版,其用作天线和硬盘驱动器的支架。

将您的拇指放入底壳预留的凹陷处。
  • 将您的拇指放入底壳预留的凹陷处。

  • 逆时针旋转底盖,直到底盖上的白点与外壳上的环对齐。

添加评论

倾斜mini,以允许底盖脱离外壳。
  • 倾斜mini,以允许底盖脱离外壳。

  • 取下底盖,放在一边。

添加评论

  • 移除靠近天线版旁边将风扇与逻辑板相固定的11.3mm T6 梅花螺丝。

There are actually 3 T6 screws securing the fan. The third screw is out of the screenshot, just below the RAM.

inferno10 - 回复

Nope, that third screw is actually just a post that the rubber grommet attached to the fan body slips over. Step 4 shows how the fan comes off of it. When you go to remove the fan, you simply remove the two screws closest to the antenna plate and then lift the fan off this post. The screw you are talking about is removed in Step 14 and does not need to be removed until this point.

Andrew Bookholt -

Successful install completed, but I had some trouble getting the fan reinstalled. When I removed the fan from the "Step 14" post, the rubber piece stayed on the post. When attempting to reinstall the fan, it was impossible to get the loop to go back over that rubber piece. So, I had to remove the post (again), and with the help of the spudger and some patience, worked it through. Then installed the fan using the 2 screws and the post. I think it may have saved some time and trouble if I just removed all 3 in the first place, leaving the post in the fan.

meag -

On mine I needed to remove the 26 mm T6 Torx standoff during this step rather than step 12

philipashlock - 回复

on my mid-2011 mac mini, that 3rd T6 post/screw had to be removed to get the fan out. It goes right through a hole in the fan housing. No way the grommet is slipping over anything without wreaking major havoc.

Derek Shaw - 回复

On my mid-2010 mac mini, also removed the 26 mm T6 Torx standoff during this step instead of step 12. Having completed the steps, it appears my hard drive is from mid 2011, so maybe the production line for mine had changed.

jstraath - 回复

  • 将距离RAM最近的风扇的耳朵从固定在外壳上的支座上抬起。

Whats a standoff? Is that a screw?

brzmn - 回复

A standoff is like a screw extender. It screws into a screw-hole, and its head has a screw hole on it. When you attach something to a standoff, it makes that something stand off the original screw-hole surface.

cityzen -

Pulling on the ear didn't do anything, so I removed the whole screw at this step. The screw stayed fixed on the fan and I didn't have to remove it at the step where you remove the logic board screws.

Probably I didn't want to use too much force .. but it worked

Alexander Kogler - 回复

This is the approach I used. no way was the "ear" pulling over the head of the standoff without breaking something. The standoff simply unscrewed from whatever is under the logic board and stayed with the fan assembly. WAY safe

Derek Shaw -

Loosen the fan standoff from the motherboard using a T6 driver.

bobcloninger - 回复

When I pulled the fan ear off the standoff the rubber grommet stayed on the standoff. That's fine, but it makes it difficult to put the fan ear back on during reassembly. So I just pulled the rubber grommet off the standoff and put it into the hole in the fan ear. Then I was able to push the fan ear onto the standoff with out trouble during reassembly.

dhein - 回复

It seems easiest to just remove this screw now. It comes out in Step 12 anyway. This way you don't have to mess with the rubber grommet.

moecastleton - 回复

  • 将风扇从mini中取出,以便有足够的空间接触到其连接器。

  • 小心地向上拉风扇电缆,将风扇连接器从逻辑板上的插座上抬起。

  • 卸下风扇。

I was a bit too rough in unclipping the fan and broke off the connector on the board?

Is my only option to replace the board?

Anthony DeFreitas - 回复

  • 移除单个一颗将整流罩与散热槽固定的3.5mm 梅花螺丝。

This is a screw into the head of another screw below it that holds the main board. When I took out the fan, the top screw AND the longer 26 mm screw came out together so when I was putting my mini back together I thought for a moment I had lost a screw.

info - 回复

Mine is stuck together too, but with a twist. They are not coming off. It starts to "jump" in the end, probably because the cover is pushing inwards the metal case. Any suggestion?

douglaslondrina - 回复

In my Mac mini there is no cowling. Maybe a previous owner didn’t put it back?

Doeke Zanstra - 回复

  • 从靠近天线板的一端抬起整流罩。

  • 将整流罩从外壳上旋开,并从mini上取下。

This is wrong step. If you need remove this out, it would be better to pull out logic board, and remember to remove cables attached on it before pull out.

Lin Adison - 回复

  • 移除将mini与天线板相固定的螺丝。

    • 2颗6.6mm T8 梅花螺丝。

    • 2颗 5.0mm T8 梅花螺丝或者 2.0mm 六角螺丝。(两者之一都可能出现。)

The red circled screws are T9 in my Mac mini (not T8).

Sven Harmstorf - 回复

ditto here - the 6.6 mm screws that anchor to the HD (now SSD) are T9

Derek Shaw -

I have tried several times but I have been unable to get all four holes to line up when replacing the antenna plate. I can get the two closer to the center of the mini just fine but no matter how I align the plate, one of the screws closer to the edge of the mini will be so far out of alignment that I cannot get the screw to go in. I had to leave one screw uninstalled. The plate is not distorted in any way. It is installed the same way it was before I removed, as far as I can tell. I am baffled! Has anyone been through this?

GalvanicMacPro - 回复

Galvanic, it pops in.

bkbkbk -

I had a really hard time with this. I was able to resolve it though: secure the other three screws first. Then I pushed my precision screwdriver into the hole and levered the wayward tab into position: it wedged in with an audible snap sound! Then I was able to fasten the final screw.

Aaron Vegh -

I have trouble with this step every time I repair one of these minis. Aaron, your tip worked perfectly for me, thanks. -Anne

DA IT Department -

The antenna plate assembly is a tongue and groove type. The plate has a "groove" and the rim of the outer case is the "lip". You have to slide it in and align the parts ant it fits perfectly .

jvilella -

To solve this, just pick on the plate on the semi circle side and with the tool "open" just slighter the space where the semicircle have to fit

Pedro -

Had the same problem - the reason was the replacement drive I used - it is thinner than the original one. So I could not get the far side of the drive correctly into the holes for the notches mounted on the drive; that is - the drive was always a little bit too far to the center of the mac case. Everything works fine until you try to install all four screws.

I found a simple solution: I attached some adhesive tape temporarily to the drive cover. By pulling on the tape while pushing the drive in its space the notches slipped into their holes. After this installing the antenna was no problem any more.

Erwin Sommerauer -

I had a similar problem with getting the antenna cover to fit back into place. I tried putting 3 screws back in and levering the 4th, but it did not work in my case. Finally, with three screws in place,, I carefully placed a thin pair of forceps into one of the holes in the cover and levered the entire cover upwards. That worked for me.

Don - 回复

Pulling up on the cover worked for me too. I found that the best place to pull up on the cover is at about "true north" in the picture ... near the black dot used to indicate lid-is-closed. I did it before installing any screws and all four screws went in fine.

Fred Cat -

As others have noted, the hardest part of the whole process is getting the holes lined up in reassembly. I ended up stripping one of the short screws, but it fits well enough to engage the slots in the circular plastic cover. If you leave a short screw out, I don't know how the bottom cover would fit securely. I would carefully note how the antenna cover fits while you remove it. The longer screws go into the actual hard drive, so I think alignment of the hard drive is part of the problem.

Steve Dollar - 回复

I had same problem..! U tried EVERTHING, and what worked PERFECT for me, and with very little effort is what "x10target" described here (scroll about half way down): Difficulty in re-installing Antenna Plate

Mikey Marvel - 回复

To replace the antenna plate, you need to patiently align the sides of the antenna and slide it in. I had similar problems as described above but, instead of using force, I resorted to patience. The plate's fit is very snug, just a little bit off the straight line and it won't sit properly. And when it sits, it really sits tight, you don't even need to hold it in place while screwing the screws back in.

Eric Schneider - 回复

In the “arch” of the plate is sort of a tongue & groove that fits over & under the lip of the body. I used Kelly Forceps to coax everything back together.

tom - 回复

  • 在接近RAM处轻轻地提起天线板。

  • 小心地将天线版径直从电路板边缘从外壳中拉动。

  • 此时切勿移走天线版,它仍然与AirPort/ 蓝牙板连接。

When I tried to do step 9 and disconnect these connectors, I found that not only the cable/connector but the receptacle tore off the logic board -- momentary panic! This happened to both connectors.

Left on the logic board were two tiny fragile gold pins (per connector). Fortunately they were pretty straight, and upon re-assembly, I was able to gently slot the receptacles back into the tiny pins. Upon reassembly, everything's working fine (no crazy fan noise) so I guess I got lucky...maybe VERY lucky. :)

Thanks iFixIt for a fantastic guide. I've got a replacement drive in there and it's definitely going to extend the life of my Mini for another season.

David Das - 回复

  • 使用挑线器的简短来小心地将天线连接头从AirPort/蓝牙板上拔出。

I broke the connector on the bluetooth board when trying to remove the antenna when I tried to replace the hard drive. Currently, the exact replacement bluetooth board 607-6509A is very hard to find or otherwise, expensive. Instead, I was able to use a cheap replacement that can be found on eBay: Apple Macbook Unibody A1342 Airport Bluetooth Module 607-6771A. There is a black plastic sheath at the back of the 607-6771A. Just cut out the part that cover the 2 holes, you are good to go.

millicurie77 - 回复

Good info, thanks

maccentric -

Hmmm just broke the port as well; it is tricky and sticky even after the port came off …

Choat - 回复

Thanks for the info; my port just broke here as well :( It is sticky and port connector is so fragile!

Choat - 回复

it’s so painful ! almost all the time is spend to try to put this ridiculous connector. my last mini mac is a server, and use ethernet not the wifi so i gave up after 1 hour .

admin - 回复

It would be nice if there was a close up pic of the different connectors. Then, one would know how the connectors attach. In this case, this connector is kinda like an old “F” plug. Used Kelly Forceps to pull straight up. Came off and went back on. No sweat.

tom - 回复

  • 从mini上取下天线版。

When you replace the antenna plate, it can be tricky. The curved edge of it actually slots both over and under the edge of the case. If it doesn’t seem to fit properly, the edges of the cut perforations may be slightly squashed. Tweak them with a small screwdriver and it will suddenly seat properly.

Ben G - 回复

结论

按照本指南相反步骤来重新组装设备。

10等其他人完成本指南。

特别感谢这些译者︰

88%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

GalvanicMacPro, to my recollection, the plate needs to be more fully inserted before all screws will line up again.

bkbkbk - 回复

bkbkbk,

I can see that it has a very particular orientation, going under the Mini's housing from about 10 o'clock to 2 o'clock, so to speak, and that I've done. I can't for the life of me see how it ever lined up originally!

GalvanicMacPro -

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 9

过去的30天: 27

总计 24,887