简介

使用本指南来移除小的塑料整流罩,用于导流冷空气引向散热器。

配件

无需配件。

将您的拇指放入底壳预留的凹陷处。
  • 将您的拇指放入底壳预留的凹陷处。

  • 逆时针旋转底盖,直到底盖上的白点与外壳上的环对齐。

添加评论

倾斜mini,以允许底盖脱离外壳。
  • 倾斜mini,以允许底盖脱离外壳。

  • 取下底盖,放在一边。

添加评论

  • 移除靠近天线版旁边将风扇与逻辑板相固定的11.3mm T6 梅花螺丝。

There are actually 3 T6 screws securing the fan. The third screw is out of the screenshot, just below the RAM.

inferno10 - 回复

Nope, that third screw is actually just a post that the rubber grommet attached to the fan body slips over. Step 4 shows how the fan comes off of it. When you go to remove the fan, you simply remove the two screws closest to the antenna plate and then lift the fan off this post. The screw you are talking about is removed in Step 14 and does not need to be removed until this point.

Andrew Bookholt -

Successful install completed, but I had some trouble getting the fan reinstalled. When I removed the fan from the "Step 14" post, the rubber piece stayed on the post. When attempting to reinstall the fan, it was impossible to get the loop to go back over that rubber piece. So, I had to remove the post (again), and with the help of the spudger and some patience, worked it through. Then installed the fan using the 2 screws and the post. I think it may have saved some time and trouble if I just removed all 3 in the first place, leaving the post in the fan.

meag -

On mine I needed to remove the 26 mm T6 Torx standoff during this step rather than step 12

philipashlock - 回复

on my mid-2011 mac mini, that 3rd T6 post/screw had to be removed to get the fan out. It goes right through a hole in the fan housing. No way the grommet is slipping over anything without wreaking major havoc.

Derek Shaw - 回复

On my mid-2010 mac mini, also removed the 26 mm T6 Torx standoff during this step instead of step 12. Having completed the steps, it appears my hard drive is from mid 2011, so maybe the production line for mine had changed.

jstraath - 回复

  • 将距离RAM最近的风扇的耳朵从固定在外壳上的支座上抬起。

Whats a standoff? Is that a screw?

brzmn - 回复

A standoff is like a screw extender. It screws into a screw-hole, and its head has a screw hole on it. When you attach something to a standoff, it makes that something stand off the original screw-hole surface.

cityzen -

Pulling on the ear didn't do anything, so I removed the whole screw at this step. The screw stayed fixed on the fan and I didn't have to remove it at the step where you remove the logic board screws.

Probably I didn't want to use too much force .. but it worked

Alexander Kogler - 回复

This is the approach I used. no way was the "ear" pulling over the head of the standoff without breaking something. The standoff simply unscrewed from whatever is under the logic board and stayed with the fan assembly. WAY safe

Derek Shaw -

Loosen the fan standoff from the motherboard using a T6 driver.

bobcloninger - 回复

When I pulled the fan ear off the standoff the rubber grommet stayed on the standoff. That's fine, but it makes it difficult to put the fan ear back on during reassembly. So I just pulled the rubber grommet off the standoff and put it into the hole in the fan ear. Then I was able to push the fan ear onto the standoff with out trouble during reassembly.

dhein - 回复

It seems easiest to just remove this screw now. It comes out in Step 12 anyway. This way you don't have to mess with the rubber grommet.

moecastleton - 回复

  • 将风扇从mini中取出,以便有足够的空间接触到其连接器。

  • 小心地向上拉风扇电缆,将风扇连接器从逻辑板上的插座上抬起。

  • 卸下风扇。

I was a bit too rough in unclipping the fan and broke off the connector on the board?

Is my only option to replace the board?

Anthony DeFreitas - 回复

  • 移除单个一颗将整流罩与散热槽固定的3.5mm 梅花螺丝。

This is a screw into the head of another screw below it that holds the main board. When I took out the fan, the top screw AND the longer 26 mm screw came out together so when I was putting my mini back together I thought for a moment I had lost a screw.

info - 回复

Mine is stuck together too, but with a twist. They are not coming off. It starts to "jump" in the end, probably because the cover is pushing inwards the metal case. Any suggestion?

douglaslondrina - 回复

In my Mac mini there is no cowling. Maybe a previous owner didn’t put it back?

Doeke Zanstra - 回复

  • 从靠近天线板的一端抬起整流罩。

  • 将整流罩从外壳上旋开,并从mini上取下。

This is wrong step. If you need remove this out, it would be better to pull out logic board, and remember to remove cables attached on it before pull out.

Lin Adison - 回复

结论

按照本指南相反步骤来重新组装设备。

5等其他人完成本指南。

特别感谢这些译者︰

100%

Leon赵国鑫正在帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

添加评论

浏览统计数据:

过去的24小时: 1

过去的7天: 7

过去的30天: 14

总计 6,217