跳转到主内容

Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement

你所需要的

  1. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement, Capacitors: 步骤 1 中的图像 1,3 Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement, Capacitors: 步骤 1 中的图像 2,3 Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement, Capacitors: 步骤 1 中的图像 3,3
    • Obtain (4) 1000uF capacitors rated for 25 volts. The replacement capacitors featured in this guide were purchased from Digi-key. Digi-key part number: UHE1E102MHD6. http://search.digikey.com/scripts/DkSear...

    • Additional suggested tools for this repair are pictured.

  2. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 2 中的图像 1,1
    • Caution: Be mindful of the dangerous high voltage that exist in this device when powered and for a short time afterward.

    • Place the camera upside down.

    • Using a small flat tool, pry off the plastic covers on each side of the case (outlined in orange)

  3. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 3 中的图像 1,1
    • Removal of the covers reveal six philips head screws (green highlight).

    • Unscrew all six screws.

  4. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 4 中的图像 1,2 Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 4 中的图像 2,2
    • Flip the camera so the top is right-side up.

    • Remove the top of the case.

    • Notice the four damaged capacitors C26, C27, C31 and C32 (red highlight).

  5. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 5 中的图像 1,1
    • Unscrew all four phillips head screws in each corner (green highlight).

    • Disconnect power cable (yellow highlight).

    • Lift and remove the clear front plastic lens cover.

    • Lift the circuit board and camera assebly out of the case.

    • Carefully separate the LED assembly from the four small connectors (highlighted in blue). Note: This step is not required for this repair. However, it reduces the possibility of inadvertent damage during the process.

  6. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 6 中的图像 1,3 Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 6 中的图像 2,3 Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 6 中的图像 3,3
    • Desolder and remove the four capacitors (red highlight).

    • Suggestion: Mark the capacitors on top and on the bottom of the board to avoid damaging another component.

  7. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 7 中的图像 1,1
    • Clean and remove remaining solder or debris from the area.

    • Cut leads on new capacitors to fit.

    • Solder the four new capacitors in place.

    • Notice: Pay attention to the polarity of the capacitors.

    • Insulate the leads and gently bend the capacitors to fit.

  8. Logitech WiLife and LukWerks Outdoor Security Camera Capacitor replacement: 步骤 8 中的图像 1,1
    • Suggestion: Before full reassembly, reattach the LED module, place the board and camera module into the case and reconnect the A/C cable to ensure proper operation.

    • Caution: Be mindful of the dangerous high voltage that exist in this device when powered and for a short time afterward.

结论

To reassemble your device, follow these instructions in reverse order.

6等其他人完成本指南。

一条评论

I did the repair worked for 5 min's then starts acting up. Before the fix wouldn't work at all. Is there anymore suggestions?

martin - 回复

添加评论

浏览统计数据:

过去 24 小时: 2

过去 7 天: 2

过去 30 天: 13

总计 9,591