修复你的物品 社区 商店

Logitech G935 Partial Left-Side Disassembly

简介

This is a guide to do a partial disassembly of the left-side of a Logitech G935. This is my daily-use headset, so I went as far as I was comfortable with knowing I could safely disassemble and reassemble without breaking tabs, glue, wires, or anything else like that.

After disassembly, reassembly is easy reversing these steps.

  1. Logitech G935 Partial Left-Side Disassembly, Remove the ear cup: 步骤 1 中的图像 1，2 Logitech G935 Partial Left-Side Disassembly, Remove the ear cup: 步骤 1 中的图像 2，2

    • Remove the ear cup. It is slightly elastic and may be gently stretched off, starting at one point and gently working around the perimeter. A spudger may help in both removal, and especially re-installation.

    编辑

  2. Logitech G935 Partial Left-Side Disassembly, Open the section: 步骤 2 中的图像 1，2 Logitech G935 Partial Left-Side Disassembly, Open the section: 步骤 2 中的图像 2，2

    • Remove the 6 Phillips #0 screws retaining the top section.

    • Gently pull off the section you just unscrewed. Flipping it upside-down off to the side is a good bet.

    • Note there is a thin cable soldered to both halves. Be very gentle with this, as I suspect repair will be near-impossible. (It's surface-mounted on the PCB, and sealed inside the driver.)

    编辑

  4. Logitech G935 Partial Left-Side Disassembly, Remove the speaker daughterboard: 步骤 3 中的图像 1，2 Logitech G935 Partial Left-Side Disassembly, Remove the speaker daughterboard: 步骤 3 中的图像 2，2

    • Remove the 2 screws holding the rear plastic facade that retains the buttons and volume wheel.

    • Carefully pull the daughterboard out. Note there is a plastic tab retaining it, but with the facade out of the way, the board is easily removed. Also note there is a ribbon cable attaching it to the mainboard.

    • Detach the ribbon cable from the daughterboard.

    编辑

  5. Logitech G935 Partial Left-Side Disassembly, Remove the microphone daughterboard: 步骤 4 中的图像 1，3 Logitech G935 Partial Left-Side Disassembly, Remove the microphone daughterboard: 步骤 4 中的图像 2，3 Logitech G935 Partial Left-Side Disassembly, Remove the microphone daughterboard: 步骤 4 中的图像 3，3

    • Remove the ribbon cable connecting the daughterboard to the mainboard.

    • Open the microphone to expose a hidden screw

    • Remove the screw retaining the front plastic facade.

    • The microphone will now come out. Take care as it's attached to the daughterboard via a small fragile soldered cable.

    • With the microphone out, remove the screw retaining the daughterboard.

    • Gently pry the daughterboard out. Prying from the curved section towards the screw (as the yellow arrow points) worked well for me.

    • Take care once the daughterboard is free, as it is still connected to the mainboard via soldered wires.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

11等其他人完成本指南。

作者

与3其他贡献者

Eric

于11/23/20注册

442 声望

撰写一个指南

徽章: 6

+ 3更多徽章

一条评论

Thanks! It helped a lot. Mine was having a problem with the power on slider, I sprayed a little bit of contact cleaner and a little bit of rubbing with a soft brush, it's working like new now!

Eduardo H. Camargo - 回复

添加评论

浏览统计数据:

过去 24 小时： 5

过去 7 天： 42

过去 30 天： 210

总计 2,369