跳转到主内容

修复你的物品

维修的权力

商店

工具

配件

  1. On the bottom side of the webcam, remove the stickers from both sides On the bottom side of the webcam, remove the stickers from both sides
    • On the bottom side of the webcam, remove the stickers from both sides

  2. Remove the four Phillips screws.
    • Remove the four Phillips screws.

    • Press the holes to unlock the side covers.

  3. Once you removed the side covers, release all the eight Phillips screws. Once you removed the side covers, release all the eight Phillips screws.
    • Once you removed the side covers, release all the eight Phillips screws.

  4. Remove the lens' crystal cover. Remove the five Phillips screws from the metal support. Remove the microphone's rubbers (one from each side).
    • Remove the lens' crystal cover.

    • Remove the five Phillips screws from the metal support.

    • Remove the microphone's rubbers (one from each side).

  5. Carefully remove the metal supports from the webcam's base.
    • Carefully remove the metal supports from the webcam's base.

  6. Carefully remove the plastic support's base. Loosen the three screws that secure the electronic circuit.
    • Carefully remove the plastic support's base.

    • Loosen the three screws that secure the electronic circuit.

  7. Disconnect the USB cable connector.
    • Disconnect the USB cable connector.

  8. Remove the electronic circuit.
    • Remove the electronic circuit.

  9. Release the clips that secure the cable holder. Pull that cable holder, out of the camera. Release the clips that secure the cable holder. Pull that cable holder, out of the camera.
    • Release the clips that secure the cable holder. Pull that cable holder, out of the camera.

  10. Front and back images of the webcam's electronic circuit board. Front and back images of the webcam's electronic circuit board.
    • Front and back images of the webcam's electronic circuit board.

  11. The problem was the broken cable on the back of the camera. I've cut the faulty part and redid the connections by welding them and insulated them with heat shrinking tubes.
    • The problem was the broken cable on the back of the camera. I've cut the faulty part and redid the connections by welding them and insulated them with heat shrinking tubes.

  12. Repaired cable and attached to the camera. Coated it with some crepe tape. Camera tested: OK!
    • Repaired cable and attached to the camera. Coated it with some crepe tape. Camera tested: OK!

    • Assemble the webcam following the steps in a reverse order.

结论

To reassemble your device, follow these instructions in reverse order.

15等其他人完成本指南。

特别感谢这些译者︰

100%

这些翻译人员帮助我们修复这个世界! 想要作出贡献?
开始翻译 ›

Jose Gustavo Abreu Murta

于2010年07月06日注册

3,431 信誉积分

创作了7篇指南

Excellent! Helped me figure out how to get the base off to mount it to an ikea worklamp as a hacky boom.

Cory Elsmore - 回复

thanks for an excellent guide . I am now more positive that it is something I can perform now. Many thanks

Graham Klaer - 回复

im having trouble releasing the 4 screws on step 3!!! the screw driver keeps slipping and i’ve tried a few and another webcam…

Dojo Mats - Sunny - 回复

Dojo, Use the correct screw driver. So easy to unscrew.

If you have damaged the screw head, you can use pliers. You will need to replace the damaged screws.

Jose Gustavo Abreu Murta -

They’re quite tight screws on the ones I’ve worked on . Super, super soft metal too, very easy to strip out.

Catherine Mateo -

添加评论

浏览统计数据:

过去的24小时: 42

过去的7天: 201

过去的30天: 860

总计 16,026