跳转到主内容

本指南有最近更改,您可查看未经巡查的最新版本

Logic Board Connectors

仅作为前提条件
本指南仅用作其他指南的先决条件。不能单独食用。

你所需要的

  1. Logic Board Connectors, Disconnect the logic board: 步骤 1 中的图像 1,2 Logic Board Connectors, Disconnect the logic board: 步骤 1 中的图像 2,2
    • Use the flat end of a spudger to disconnect the camera cable connector by prying it straight up from its socket.

  2. Logic Board Connectors: 步骤 2 中的图像 1,1
    在这个步骤中使用的工具:
    Standoff Screwdriver for iPhones
    $5.49
    购买
    • Remove the two screws securing the rear-facing camera bracket:

    • One 3.0 mm standoff screw

    • One 3.1 mm Phillips screw

    • Standoff screws are best removed using a standoff screwdriver or bit.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  3. Logic Board Connectors: 步骤 3 中的图像 1,1
    • Remove the rear-facing camera bracket.

  4. Logic Board Connectors: 步骤 4 中的图像 1,2 Logic Board Connectors: 步骤 4 中的图像 2,2
    • Use the point of a spudger to disconnect the flash connector from its socket by prying it straight up.

  5. Logic Board Connectors: 步骤 5 中的图像 1,1
    • Remove the two screws securing the upper cable bracket:

    • One 2.9 mm Phillips screw

    • One 1.3 mm Phillips screw

  6. Logic Board Connectors: 步骤 6 中的图像 1,1
    • Remove the upper cable bracket.

  7. Logic Board Connectors: 步骤 7 中的图像 1,2 Logic Board Connectors: 步骤 7 中的图像 2,2
    • Use the flat end of a spudger to pry the upper cable connector up from its socket.

  8. Logic Board Connectors, Remove the top left antenna component: 步骤 8 中的图像 1,1
    • Remove the three Phillips 1.3 mm screws securing the top left antenna component.

  9. Logic Board Connectors: 步骤 9 中的图像 1,1
    • Remove the 1.4 mm Phillips screw securing the antenna component to the top of edge of the case.

  10. Logic Board Connectors: 步骤 10 中的图像 1,1
    • Remove the antenna component.

  11. Logic Board Connectors, Remove the top left grounding clip: 步骤 11 中的图像 1,1
    • Remove the two Phillips screws securing the grounding clip at the top left edge of the logic board:

    • One 1.5 mm Phillips screw

    • One 2.6 mm Phillips screw

  12. Logic Board Connectors: 步骤 12 中的图像 1,1
    • Remove the grounding clip.

  13. Logic Board Connectors, Unscrew the logic board: 步骤 13 中的图像 1,1
    • Remove the three screws securing the motherboard:

    • One 1.8 mm Phillips screw

    • One 2.5 mm standoff screw

    • One 2.2 mm standoff screw

  14. Logic Board Connectors: 步骤 14 中的图像 1,2 Logic Board Connectors: 步骤 14 中的图像 2,2
    • Use tweezers to gently bend the logic board grounding bracket out of the way.

  15. Logic Board Connectors: 步骤 15 中的图像 1,2 Logic Board Connectors: 步骤 15 中的图像 2,2
    • Use the point of a spudger to move the SIM card eject plunger out of the logic board's way.

结论

To reassemble your device, follow the above steps in reverse order.

Take your e-waste to an R2 or e-Stewards certified recycler.

Repair didn’t go as planned? Check out our Answers community for troubleshooting help.

Arthur Shi

于01/03/18注册

248,439 声望

创作了503篇指南

团队

iFixit iFixit 的会员

Staff

136 名成员

创作了16,573篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时: 0

过去 7 天: 0

过去 30 天: 0

总计 206