跳转到主内容

当前版本的文档还未经巡查,您可以查看最新的已查核版本

你所需要的

  1. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 1 中的图像 1,3 : 步骤 1 中的图像 2,3 : 步骤 1 中的图像 3,3
    • Loosen the guitar strings using a string winder.

    • The three strings closest unwind clockwise and the three farther away unwind counterclockwise.

    • Using a coin, carefully begin unscrewing and removing the tailpiece.

    • You can use a flat head screwdriver, but it will damage the finish on your tailpiece.

    • Remove the tailpiece by completely unscrewing it from the metal inserts and then gently lifting the assembly out of the body and set off to the side.

  2. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 2 中的图像 1,1
    • Use the Phillips #0 screwdriver to remove the eight screws keeping the pickups in place.

    • All screws are the same size.

  3. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 3 中的图像 1,3 : 步骤 3 中的图像 2,3 : 步骤 3 中的图像 3,3
    • Note which color wire is coming out of each pickup.

    • Gently flip over your guitar and put it on a soft towel or other soft material. Take off the control cavity cover.

    • Desolder the wires of the pickup from the terminal that is touching the back of the potentiometer, or pot.

    • A potentiometer is what the pickups are wired to that allow the player to have on-board control of their volume and tone. Terminals are the parts on a potentiometer that you solder the wires to.

  4. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 4 中的图像 1,1
    • Flip over your guitar again. Thread the wire of the new pickup through the body to the control cavity and screw in the pickup using the Phillips #0 screwdriver.

    • Check what color wire is coming from each pickup.

    • For these kinds of pickups, the neck pickup magnet should face the neck and the bridge pickup magnets should face the bridge.

  5. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 5 中的图像 1,1
    • Do not touch the soldering iron, or let it touch anything but the solder and wires.

    • The pickup wire should have multiple wires inside it. Check with the manufacturer which wire is which.

    • Solder the new ground wires to the back of the volume pots or to the terminal touching the back of the pot.

  6. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 6 中的图像 1,1
    • Do not touch the metal parts of the soldering iron or the solder after melting it, they will burn you.

    • Relative to the output jack, the bottom row is for the bridge pickup and the top row is for the neck pickup.

    • Identify your hot wires and volume pots and solder the hot wire to the center terminal of the wires corresponding pot.

  7. 这个步骤还没有翻译 帮忙翻译一下

    : 步骤 7 中的图像 1,1
    • Screw back on the control cavity cover and flip over your guitar.

    • Reattach the tailpiece and tune your guitar.

    • Raise and lower the pickups as desired using the two screws on the sides of the pickup rings.

终点

2等其他人完成本指南。

0条评论

添加评论

浏览统计数据:

过去 24 小时: 1

过去 7 天: 10

过去 30 天: 33

总计 965