跳转到主内容

修复你的物品

维修的权力

商店

简介

A functioning microphone is essential to any phone call. If this function stops working, it may need to be replaced. A faulty microphone could result in poor audio during recorded videos or the receiver of a phone call having difficulty hearing the user, as the microphone would not be properly picking up sounds. This guide teaches you how to replace the microphone on an LG VX4400 cell phone. Before beginning, be sure to power off the device.

  1. Press the light grey button in the top-center on the back of the phone. While pressing, slide the battery and cover up. While pressing, slide the battery and cover up.
    • Press the light grey button in the top-center on the back of the phone.

    • While pressing, slide the battery and cover up.

  2. Unscrew the antenna by grasping the base and twisting counterclockwise.
    • Unscrew the antenna by grasping the base and twisting counterclockwise.

    • The antenna may separate from a black sleeve during removal. You may need to use tweezers to remove the sleeve. Remove both the antenna and the sleeve and set aside.

  3. The phone may have a rubber insert in the bottom of the phone (see picture). If this rubber insert exists, remove it from the bottom of phone and set aside. The phone may have a rubber insert in the bottom of the phone (see picture). If this rubber insert exists, remove it from the bottom of phone and set aside. The phone may have a rubber insert in the bottom of the phone (see picture). If this rubber insert exists, remove it from the bottom of phone and set aside.
    • The phone may have a rubber insert in the bottom of the phone (see picture). If this rubber insert exists, remove it from the bottom of phone and set aside.

  4. 打开所有标签

    Mac的RAM升级套装

    购买套装

    所有选项卡都有足够的 RAM

    购买套装
  5. Use a Torx T6 screwdriver to unscrew the four screws on the back of the phone. The bit size is engraved on the base of the bit head.
    • Use a Torx T6 screwdriver to unscrew the four screws on the back of the phone.

    • The bit size is engraved on the base of the bit head.

  6. With the phone flipped open, wedge the back cover from the faceplate by running the tip of the plastic opening tool around the seam on the back of the phone. Gently pull the two pieces apart to separate, and set the back casing aside. Apply enough force to separate the pieces without cracking the back cover.
    • With the phone flipped open, wedge the back cover from the faceplate by running the tip of the plastic opening tool around the seam on the back of the phone.

    • Gently pull the two pieces apart to separate, and set the back casing aside.

    • Apply enough force to separate the pieces without cracking the back cover.

  7. Lift the motherboard to gain access to the keypad and side buttons beneath.
    • Lift the motherboard to gain access to the keypad and side buttons beneath.

    • The motherboard is attached with a thin ribbon cable at the upper right corner of the case. Be careful not to break the cable.

  8. Using your fingers or the pointed end of a black plastic spudger, pry the microphone out and replace. Using your fingers or the pointed end of a black plastic spudger, pry the microphone out and replace. Using your fingers or the pointed end of a black plastic spudger, pry the microphone out and replace.
    • Using your fingers or the pointed end of a black plastic spudger, pry the microphone out and replace.

结论

To reassemble your device, follow these instructions in reverse order.

Nico Chiarito

于2010年01月21日注册

22 信誉积分

创作了5篇指南

团队

Cal Poly, Team 8-47, Regan Winter 2010 Cal Poly, Team 8-47, Regan Winter 2010 的会员

CPSU-REGAN-W10S8G47

5 名成员

创作了8篇指南

添加评论

浏览统计数据:

过去的24小时: 0

过去的7天: 0

过去的30天: 0

总计 1,694