跳转到主内容

简介

This guide will show you the steps to replace a damaged rear facing camera.

  1. While holding the battery release button, pull the bottom end of the phone out of the body. While holding the battery release button, pull the bottom end of the phone out of the body.
    • While holding the battery release button, pull the bottom end of the phone out of the body.

  2. Insert the sim card eject tool (0.8mm sim card eject head) into the small hole on the sim card tray. Press inward with some force to eject the tray. Pull the sim card tray out of the phone.
    • Insert the sim card eject tool (0.8mm sim card eject head) into the small hole on the sim card tray.

    • Press inward with some force to eject the tray.

    • Pull the sim card tray out of the phone.

  3. Remove the two 5.5mm Phillips #00 screws from the base of the phone. Remove the two 5.5mm Phillips #00 screws from the base of the phone.
    • Remove the two 5.5mm Phillips #00 screws from the base of the phone.

  4. Insert the plastic opening tool into the seam between the glass screen and the metal body.
    • Insert the plastic opening tool into the seam between the glass screen and the metal body.

    • Pry the glass from the body only a slight amount.

  5. Insert the Spudger into the now open space between the body and screen. Push inward to separate the screen even more.
    • Insert the Spudger into the now open space between the body and screen.

    • Push inward to separate the screen even more.

    • Slowly slide the nylon spudger up the edge the phone till the screen pops out of the body.

    • When putting the screen back in, press the edges down from the top of the phone to the bottom. The screen should "pop" into place.

  6. Peel the screen away from the body.  The two parts should be completely separated. Peel the screen away from the body.  The two parts should be completely separated.
    • Peel the screen away from the body. The two parts should be completely separated.

  7. Insert the plastic opening tool between the camera-ribbon connector and the motherboard, then pull up. It should pop out easily. Insert the plastic opening tool between the camera-ribbon connector and the motherboard, then pull up. It should pop out easily. Insert the plastic opening tool between the camera-ribbon connector and the motherboard, then pull up. It should pop out easily.
    • Insert the plastic opening tool between the camera-ribbon connector and the motherboard, then pull up. It should pop out easily.

  8. After detaching the ribbon, carefully remove the camera using tweezers After detaching the ribbon, carefully remove the camera using tweezers
    • After detaching the ribbon, carefully remove the camera using tweezers

结论

To reassemble your device, follow these instructions in reverse order.

30等其他人完成本指南。

Parker Reynolds

于2016年10月03日注册

833 信誉积分

创作了2篇指南

团队

Cal Poly, Team 18-2, Forte Fall 2016 Cal Poly, Team 18-2, Forte Fall 2016 的会员

CPSU-FORTE-F16S18G2

4 名成员

创作了15篇指南

This worked great and took me about 10 minutes!

Mark - 回复

Great instructions. This was my first time taking apart any phone. Everything went smoothly and my camera now works! thank you

Christopher Piatt - 回复

the camera is held down with sticky tape and I wasn’t comfortable pulling hard under the processing board, so I pulled the six screws holding that down and removed it first. Unfortunately for me the new camera still doesn’t focus…

Ray White - 回复

This worked great for me. I was a little nervous prying on my phone, especially when I heard the first POP. But after that, it was not hard at all. The new camera focuses great for me now and I can get back to taking great pictures with my G5!

Thanks for the detailed instructions, tools and affordable part!

Brad - 回复

You may want to mention that the original camera is glued in. It takes a bit of prying to pop it out.

Ryan - 回复

添加评论

浏览统计数据:

过去的24小时: 3

过去的7天: 28

过去的30天: 125

总计 15,112