跳转到主内容

KitchenAid Classic Mixer K45SSWH Worm Gear Replacement

你所需要的

  1. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement, Motor Housing Cover: 步骤 1 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement, Motor Housing Cover: 步骤 1 中的图像 2,2
    • Using a spudger, gently pry off the aluminum drip ring.

  2. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 2 中的图像 1,1
    • Using a 4 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.

  3. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 3 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 3 中的图像 2,2
    • Using a spudger, pry the planetary gear cover from the mixer shaft.

  4. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 4 中的图像 1,1
    • Using a flathead screwdriver, remove the five 28 mm front motor housing screws.

    • Using the same flathead screwdriver, remove the two 28 mm locking screws.

    • One of the locking screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  5. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 5 中的图像 1,1
    • Turn your device around. Using the same flathead screwdriver, remove the two 28 mm rear locking screws.

    • One of the rear motor housing screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  6. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 6 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 6 中的图像 2,2
    • Using a Phillips #2 screwdriver, remove the 10 mm screw from top of back cover.

    • The rear cover is now completely free from the mixer.

  7. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 7 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 7 中的图像 2,2
    • Carefully pull the power cord from the notch in back of the mixer.

    • The motor housing cover is now completely free from the base of the mixer.

  8. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 8 中的图像 1,1
    • Lift the motor housing cover from the mixer base.

    • Be sure to place the cover upside-down to prevent grease from leaking out.

  9. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement, Worm Gear: 步骤 9 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement, Worm Gear: 步骤 9 中的图像 2,2
    • Using a butter knife or putty knife, remove the grease from the gears.

    • Place the grease in motor housing cover.

  10. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 10 中的图像 1,1
    • Using a Phillips #2 screwdriver, remove the three 20 mm screws from the worm gear tower.

    • The worm gear tower assembly is now free from the mixer base.

  11. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 11 中的图像 1,2 KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 11 中的图像 2,2
    • Using a pin punch and a hammer, remove the roll pin.

  12. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 12 中的图像 1,1
    • Slide the tower gear out to access the worm gear.

  13. KitchenAid Classic Mixer K45SSWH Worm Gear Replacement: 步骤 13 中的图像 1,1
    • Remove the worm gear from the tower.

结论

To reassemble your device, follow these instructions in reverse order.

57等其他人完成本指南。

Chris Grant

于10/07/14注册

1,742 声望

撰写一个指南

团队

Cal Poly, Team 14-28, Maness Fall 2014 Cal Poly, Team 14-28, Maness Fall 2014 的会员

CPSU-MANESS-F14S14G28

4 名成员

创作了22篇指南

28条评论

Some corrections:

Step 1 -- Suggest (as the Service Manual does) using a flat-blade screwdriver and tap it with a light hammer to drive the drip ring off.

Step 2 -- the correct size pin punch is 5/32"

Step 3 -- Using two flat-blade screwdrivers, one on each side, pry off the planetary.

A plastic spudger is likely to break. Two points of leverage opposits each other distributes the load and prevents to the planetary and its shaft.

Step 11 -- The proper punch size is 3/32"

Steps 12 & 13 -- There is a washer on each side of the worm gear. Retain these and place one on each side off the grar when reassembling.

A link to the Service Manual:

http://www.kitchenaidparts.eu/documents/...

Finkerbell - 回复

Cheers Finkerbell,

Very helpful info, as was the main part of the guide.

Not sure what model number I was working on, but when I l lifted off the motor housing, there was still wires connected to the base.

Just be careful at this stage in case you have the same...

markguerin - 回复

my model K5SS WH is the same as yours until step 5. It doesnt have the two bolts as shown in the picture for step 5 so i wasnt able to complete the repair. any suggestions.

sailsetter - 回复

Wow! Lovely guide to easy maintenance, no plenty stories

Dennis - 回复

This is the BEST! Thank you.

Advanamics - 回复

添加评论

浏览统计数据:

过去 24 小时: 25

过去 7 天: 191

过去 30 天: 1,050

总计 108,631