修复你的物品 社区 商店

Jumper Angelsounds JPD-100S Indicator Light Replacement

简介

Have a working knowledge of soldering before attempting to replace this part.

你所需要的

  1. Jumper Angelsounds JPD-100S Indicator Light Replacement, Motherboard: 步骤 1 中的图像 1，1

    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

    编辑

  2. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 2 中的图像 1，2 Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 2 中的图像 2，2

    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

    编辑

  3. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 3 中的图像 1，1

    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

    编辑

  5. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 4 中的图像 1，2 Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 4 中的图像 2，2

    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

    编辑

  6. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 5 中的图像 1，2 Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 5 中的图像 2，2

    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

    编辑

  7. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 6 中的图像 1，1

    • With your hand, remove the pink component.

    编辑

  8. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 7 中的图像 1，1

    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

    编辑

  9. Jumper Angelsounds JPD-100S Indicator Light Replacement, Indicator Light: 步骤 8 中的图像 1，1

    • Place the motherboard in a position that allows access it's underside.

    • Pre-heat the soldering iron.

    编辑

  10. Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 9 中的图像 1，3 Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 9 中的图像 2，3 Jumper Angelsounds JPD-100S Indicator Light Replacement: 步骤 9 中的图像 3，3

    • Desoldering

    • If steam is created when the soldering iron is touched to a wet sponge then the soldering iron is hot enough.

    • Use the soldering iron and soldering vacuum to unsolder the indicator light leads.

    • Plastic spacer holding indicator light may burn.

    编辑
结论

To reassemble your device, follow these instructions in reverse order.

作者

与3其他贡献者

Deron Rogers

于08/31/15注册

271 声望

创作了2篇指南

徽章: 14

+ 11更多徽章

团队

USF Tampa, Team 6-1, Remmell Fall 2015 USF Tampa, Team 6-1, Remmell Fall 2015 的会员

USFT-REMMELL-F15S6G1

6 名成员

创作了6篇指南

0条评论

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 0

过去 30 天： 0

总计 175