修复你的物品 社区 商店

JBL On Stage II 30-Pin Connector Replacement

简介

This guide provides the steps necessary in order to replace the thirty-pin connector.

你所需要的

  1. JBL On Stage II 30-Pin Connector Replacement, Cracking the Case: 步骤 1 中的图像 1，1

    • Turn the device upside down so that the three rubber pads are facing up.

    翻译

  2. JBL On Stage II 30-Pin Connector Replacement: 步骤 2 中的图像 1，1

    • Use a heat gun (set to low) to apply heat to one of the rubber pads until you can easily remove the pad. This step takes around 5-7 minutes.

    翻译

  3. JBL On Stage II 30-Pin Connector Replacement: 步骤 3 中的图像 1，1

    • Remove the heated rubber pad with a plastic opening tool.

    • Repeat steps 2 and 3 for the two remaining rubber pads.

    翻译

  4. JBL On Stage II 30-Pin Connector Replacement: 步骤 4 中的图像 1，2 JBL On Stage II 30-Pin Connector Replacement: 步骤 4 中的图像 2，2

    • Remove the six 1cm T-10 torx screws on the bottom of the device (found under the rubber pads) using a T-10 Torx screwdriver.

    翻译

  6. JBL On Stage II 30-Pin Connector Replacement: 步骤 5 中的图像 1，3 JBL On Stage II 30-Pin Connector Replacement: 步骤 5 中的图像 2，3 JBL On Stage II 30-Pin Connector Replacement: 步骤 5 中的图像 3，3

    • Open the device along its seam.

    • Be careful when separating the device because there are wires connecting the two seperate halves.

    翻译

  7. JBL On Stage II 30-Pin Connector Replacement: 步骤 6 中的图像 1，1

    • Disconnect the ribbon cable connector from the top half of the device by pulling outward and parallel to the connecting pins.

    翻译

  8. JBL On Stage II 30-Pin Connector Replacement: 步骤 7 中的图像 1，2 JBL On Stage II 30-Pin Connector Replacement: 步骤 7 中的图像 2，2

    • Locate and disconnect the two molex connectors found on either side of the ribbon cable connector on the bottom half of the device.

    翻译

  9. JBL On Stage II 30-Pin Connector Replacement, 30-Pin Connector Replacement: 步骤 8 中的图像 1，1

    • Apply heat with a heatgun on a low setting to the area around the 30-pin connector until you can easily pry it out by the seam surrounding it (about 10 minutes).

    翻译

  10. JBL On Stage II 30-Pin Connector Replacement: 步骤 9 中的图像 1，1

    • Use a metal spudger to pry out the plastic surrounding the 30-pin connector.

    翻译

  11. JBL On Stage II 30-Pin Connector Replacement: 步骤 10 中的图像 1，1

    • Use a pair of tweezers to wiggle out the 30-pin connector.

    翻译
结论

To reassemble your device, follow these instructions in reverse order.

另外一个人完成了本指南。

作者

与4其他贡献者

Janessa D Cabrera

于01/23/14注册

514 声望

创作了4篇指南

徽章: 10

+ 7更多徽章

团队

Cal Poly, Team 9-28, Maness Winter 2014 Cal Poly, Team 9-28, Maness Winter 2014 的会员

CPSU-MANESS-W14S9G28

4 名成员

创作了7篇指南

2条评论

and how you get a new one of the 30 pin connector?

bini barazany - 回复

Yes, where can we buy a new one of the 30 pin connector?

Jimbo - 回复

添加评论

浏览统计数据:

过去 24 小时： 0

过去 7 天： 1

过去 30 天： 9

总计 4,426